Northtech NT 660S-30HCVS 30 HP Single Surface Planer (w/ Helical Cutter Head)

This Northtech NT-660S series single-surface planer opens wide to accept material up to 11-3/4″ (H) by 26″ (W). A soft-start 30 HP motor drives the 4″ helical cutter head with six (6) rows of two-sided inserts. The cutter head is dynamically balanced to ensure a quieter operation and smoother cuts. Feed rates from 5 to 70 FPM are precisely controlled through a variable frequency drive. Digital displays for both the feed-rate and cutter height allow quick set-up and accurate adjustment. 

Guaranteed Safe Checkout

Credit

Cutter Heads:

  •  Cutterhead Motor:  30HP, 3PH 230/460 Volt

Features:

  • The Helical 4″ cutterhead provides a high chip removal rate, superior surface finish & low noise level (under 85 dba).
  • Powerful 30HP cutterhead motor w/ wye-delta soft-start control; 1HP feed motor makes this planer ideal for heavy-duty planing.
  • The main motor is Nema-rated and standard with a 2-year warranty and service throughout North America.
  • Digital positioning controller for convenient thickness setting (with memory control to 99 thickness settings).
  • Variable feed speed is controlled by VFD with an LED readout of feeding speed.
  • Powered table elevation for fast and convenient thickness setting. The opening has been increased to 12″ on NT-660S series planers vs. 8″ on the standard NT-660 planers.  
  • Extra heavy, rib-reinforced cast iron table is surface precision ground. 660S-30HCVS has (4) precision 35mm jackscrews to support the planer’s rugged construction.
  • Adjustable bed rollers ensure fast and proper positioning with regard to rough lumber to finished glue panels.
  • UV rubber outfeed roller provides an optimum finish with reduced vibration.
  • Corrugated sectional infeed roller has an independent yield for running strip stock of varying thicknesses without the danger of kickback.
  • Anti-kickback fingers equipped at the infeed end provide added safety for the operator.
  • Raising and lowering limit controls for powered table elevation

Specifications:

  • Top Head Hp. = 30 Hp.
  • Voltage/ Freq. = 230/460 Volt 60Hz
  • Phase = 3 Phase
  • Amp Requirement = 73/37.5 Amps
  • Feed Hp. = 1 Hp.
  • Feed System = (2) Segmented/(1) Rubber Roll
  • Drive System = Belt
  • Feed Speed = 5 – 70 FPM
  • Variable Speed = Inverter Controlled
  • Elevation Hp. = 1 Hp.
  • Elevation Style = REC 727M Elevation Control
  • Elevation Sys. = (4) Post Jack Screw
  • Total Hp. = 33 Hp.
  • Electronics = CE Approved Components
  • Dual Voltage = 230/460 Volt
  • Control Voltage = 110 Volt
  • Programmable = REC 727M Elevation Control
  • Min. Length = 10”
  • Min. Width = 1″
  • Max. Width = 26″
  • Min. Thickness = 3/16″
  • Max. Thickness = 11-3/4”
  • Cutter Head RPM = 5500 RPM
  • Tooling = 15 x 15 x 2.5 mm
  • Head Type = Dynamically Balanced Helical Head
  • Cutter Head Dim = 4” x 26”
  • Cut Head Matl. = Alloy Steel
  • Rows of Cutters = 6 Rows
  • No. of Inserts = 156 Inserts
  • Insert Size = 15 x 15 x 2.5 mm
  • Dust Collection = (1) 6” @ 981 CFM
  • Digital Display = Elevation and Feed Speed
  • Powered Rollers = (3) Top Powered Rollers
  • Idle Rollers = (2) Idle Bed Rollers
  • Pressure Shoes = (13) 2” Pressure Shoes
  • Rear E Stop = Push Button
  • Frame Const. = 5/16” Steel Construction
  • Decible Rating = 70 dB
  • Net Weight = 2330 Lbs.
  • Gross Weight = 2580 Lbs.
  • Machine Dims. = 45” x 39” x 54”
  • Packaging Dims = 52” x 51” x 5