2015 HAFELE FUTURA 250 HINGE BORING, RTA, DRILLING & INSERTION MACHINE

2015 HAFELE FUTURA 250 HINGE BORING, RTA, DRILLING & INSERTION MACHINE $2,000

This machine is set up to drill and insert RTA fittings currently. Very hard to find used plus it’s a 2015 model year. Powered by a 1-1/2 hp 115V/Single Phase motor. Pneumatic drilling unit with push button controls. Ruler 600 mm (23 5/8”). Includes 2 Tilt stops with clamp lever. Worktop 600 x 400 mm (23 5/8” x 15 3/4”). Dual pneumatic hold-down clamps. Locking pin for fence depth adjustment with positive stops. You can also purchase heads for hinge boring and line boring as well.  This fully functional machine has been fully cleaned, checked, and is ready to work from the time you receive it.

2014 OMAL INSERT C HINGE BORING/INSERTION MACHINE

2014 OMAL INSERT C HINGE BORING & INSERTION MACHINE $1,750

Clean 2014 Omal Insert C hinge boring and insertion machine. 1.5 HP  230V/3 Phase motor. 5 Spindle gearbox (boring pattern 45 x 9.5mm) 82″ fence with dual flip stops. Dual pneumatic hold downs. Universal insertion RAM & operators manual, This fully functional machine has been fully cleaned, checked, and is ready to work from the time you receive it.

REFURBISHED ONSRUD 10HP INVERTED PIN ROUTER W/36″ THROAT

REFURBISHED ONSRUD 36210 INVERTED PIN ROUTER $4,500

The word “refurbished” is used all too often. With that being said this 36210 has had a lot of work done to it at some point recently. Everything was taken apart because every sq. inch, inside and out, has been nicely repainted.  It also had a new 10 hp Baldor 208-230/460V motor installed (currently wired 230V/3 Phase), 2 NEW top of the line Norgren regulators. One for the oiler and one for the main air supply. Plus multiple other parts replaced. We also replaced the plunge piston, mini regulator, and Parker belt tensioner control due to air leaks. Spindle bearings are in great condition. This is a model 36210 so it is the BIG model with the 36″ throat. While not sporting a vacuum pump the lines are there along with a Busch intake filter and housing……even sporting a newer filter! You will also get the spindle wrenches, several collets, a pair of nuts, and even a manual. There is a lot of value built into this clean, refurbished machine and it is really well done. This fully functional machine has been fully cleaned, checked, and is ready to work from the time you receive it.

MIDWEST AUTOMATION PR 1700 66″ PINCH ROLLER

MIDWEST AUTOMATION PR 1700 66″ PINCH ROLLER $4,500

Clean Midwest Automation Model PR-1700, 66″ Pinch Roller (67″ actual width). Features (2) pneumatic pressure cylinders. Max panel thickness 100 mm (2-1/8″currently/4″ possible). Max panel width 1700 mm (66″). Machine weight 907 kg (2000 lbs). It’s powered by a 1.5 hp motor currently wired 230V/3 Phase and has a feed speed 36 ft/min. This fully functional machine has been fully cleaned, checked, and is ready to work from the time you receive it.

NORDFAB/DISA/DANTHERM/NEDERMAN 3,000 CFM DUST COLLECTOR

NORDFAB/DISA/DANTHERM/NEDERMAN 3,000 CFM DUST COLLECTOR $3,500

This is a Nordfab “labeled” dust collector. This is the tallest and the smallest of the NFP series. These models are a step up from the “S” series dust collectors. This one is a model NFP-1H-OP and is very compact for a dust collector that has 288 sq. ft. of filter media. It stands 13’2″ tall, but the bag house only takes up 44-1/2″ X 44-1/2″ of floor space due to it’s height. All 16 of the “Superbag” filter bags are brand NEW! This particular model is powered by a model S56-250 direct drive 10hp combifab fan (230/460V/3 Phase) with a 10″ inlet. This fully functional machine has been fully cleaned, checked, and is ready to work from the time you receive it.

This is our favorite brand of dust collectors due to the quality of the fan, motor, over-all construction, and the quality of the bag which makes a BIG difference on how it operates under heavy dust loads. Below is some information on the bags.

Efficiency and low energy consumption
Superbag is polyester filter bag. A patented weaving technique in tubular format give the filter bag a surface which can cope with varying dust loads and with virtually any type of dust. Better filtering efficientcy is achieved with this unique filter media which provides low pressure drop, and low energy consumption.
Strength and durability
The special shape of the SUPERBAG helps to ensure that the high efficiency and effectiveness of the NFP filter system is maintained even after long periods of operation. The durability is the result of the patented construction, strong polyester fiber and seamless body. These features also help make cleaning of the filter bag very easy.
Antistatic
SUPERBAG’s interwoven carbon fiber wire provides higher anti-static properties – both on the surface and inside – than traditional filter bags. This reduces the risk of fire and explosion as fine particles are removed.
Quality Circular knitted with two integrated layers filter
Material 100% polyester
Weight 16 Ounces/sqft
Max. Operating temperature 289 ºF
Intermittent Peak temperature 320 ºF
Melting Point 482-500 ºF
BIA classification U 95.5% filtration of 0.088 gr/ft3 Test dust (90% 0,2-2,0)
Electrostatic Behavior Surface resistance 2.6 x 107 Ohm Charging towards PA 0.7 kV DIN 54 345 TEIL 1 TEFO Method 40-77
Applications Filtration of: Shavings, saw dust, sanding dust, lacquering dust from woodworking industry as well as other fibrous materials such as mineral wool, paper strips and dust.

GANNOMAT PROLINE 50 DUAL HEAD LINE BORING MACHINE

GANNOMAT PROLINE 50 DUAL HEAD LINE BORING MACHINE $5,250

Dual heads with 25 spindle per head for a total of 50 spindles on 32mm centers. Minimum distance between heads 145 mm (5-45/64″). Maximum distance between centers 608 mm (23-15/16″). Position adjustment of stopping fence 0-120mm( setback set at 37mm). Maximum work piece thickness 100 mm or 3-15/16″. Dual 2 hp motors wired 220V/3Phase.  6 Pneumatic holds downs. 14′-8″ back fence with 4 flips stops. Manual per picture. This fully functional machine has been fully cleaned, checked, and is ready to work from the time you receive it.

HARTZELL 6,000 CFM CENTRIFUGAL BLOWER 15 hp

HARTZELL 6,000 CFM CENTRIFUGAL BLOWER 15 hp $1,800

High Quality blower from a very well know company. 15 hp Reliance motor (208-230/460V/3 Phase) 6,000 CFM 18″ blower. 14″ X 20″ ID rectangle outlet with a 19″ ID round inlet. notes: very clean w/almost new motor.

2009 VOORWOOD L110A EDGE FOILER

2009 VOORWOOD L110A EDGE FOILER $$$SOLD WITH IN 24 HOURS OF LISTING$$$

You will be hard pressed to find a newer, cleaner, L110A on the market. Everything you see is wearing it’s original paint…..yes even the guards! It really is that clean!

Feed through, single sided with: (1) Shaping, (1) sanding and (1) foiling station, all units are 0° – 45° tilting. Min. part size 5″ x 2-3/4″, thickness 1/8″ to 1-1/2″ max., 1-3/4″ max. profile face.

  Equipped with: 5 HP – 6,000 RPM Shaping spindle (1-1/4″ dia.) for 6″ max. dia. tooling followed by a 1 hp sanding station.

  Foiling section: Supply roll for 2″ max. width, shaped applicator wheel with automatic heat control, adjustments 2″ in-and-out, 1-1/2″ laterally across and -10° to +50° angle from horizontal, film take-up/carrier rewinds with automatic tension control, stripper rollers for precision trimming on miters and edges.

  18 FPM Fixed feed speed, 1 HP feed drive; overhead holddown with (2) rows of tightly spaced non-marking rollers and feed chain with non-marking rubber pads, feeds from right-to-left. ~ Includes: Outrigger panel support roller track.

BONACIN PINTA AUTOMATIC FEED THROUGH CASE CLAMP

2007 BONACIN STRETTOIO PINTA AUTOMATIC FEED THROUGH CASE CLAMP $35,000

Clean, fully operational, feed through automatic case clamp with infeed conveyor.  It’s possible to assemble 1200 boxes in 8 hours at full speed. Automatically adjusts both for height and length with photoelectric cells and encoders. Bonacin utilizes a patented travel design with reinforced steel belts and powerful gear motors to “PULL the box closed”. The design is quiet, simple, yet powerful. (VERY QUIET & FAST!) This traveler system quadruples motor power and transfers it to the pressing frame to ensure square closing of boxes with multiple fixed shelves. Power is adjustable to both horizontal and vertical pressers. This system is superior to pneumatic cylinders as Bonicin allows precise pressure regulation. It is faster than screw systems.

We would rate the clamp condition as excellent while we would rate the infeed conveyor being in good condition.

Parallelism – The Bonacin Series has three 40mm (1.57”) diameter hardened guides that keep the vertical and horizontal pressing frames in true parallel with the opposing machined reference of the clamp.

Powerful – The Bonacin Series patented Traveler System uses high tech steel reinforced tooth belts to “PULL the box closed” with over 4880 lbs for a standard base cabinet.

Speed – The Bonacin Series travels from minimum to the maximum opening in 12 seconds. Up to 7 times faster than screw clamps!

Rigidity – The Bonacin Series has a continuous integrated top platen, superior to interlock systems which depend only on the strength of individual bars. This ensures a flat, even pressing surface to close all joints tightly the first time. Small boxes can be clamped in the front instead of having to be placed in the center (front to back) as required by screw clamps.

TECHNICAL SPECIFICATIONS:

Max. Clamping length 2600 mm (102”) Min. Clamping length 140 mm (5.5”) Max. Clamping height 1250 mm (49.2”) Min. Clamping height 250 mm (9.8”) Max. Clamping width 812 mm (32”) Worktable height 700 mm (27.6”) Vert. & Horz. pressure 0-1200 Kg (0-2645lbs) Currently Wired 230V/3 Phase  Weight 2,450 Kg (5400lbs)

LOW USE FRAVOL A16/S CONTOUR EDGEBANDER

LOW USE FRAVOL A16/S CONTOUR EDGEBANDER $6,500

If you are in need of a clean, low use contour edgebander look no further. You will be hard pressed to find a cleaner one!  This 2006 A16/S has seen very limited use. It features an integrated Power Feed Unit.. Edge cap. 0.4 – 3 mm (1/8″) thickness and up to 2-1/4″ height. Hot melt glue system – applies glue to panel or edge, variable glue applicator roller & banding material feed 8 – 49 FPM. Also note hoe CLEAN this glue pot it! Min. radius 20 mm (3/4″). Guillotine “end cutoff” for banding material. Worktable dimensions: 45″ x 39″. This fully functional machine has been fully cleaned, checked, and is ready to work from the time you receive it. (If you purchase this machine we will give you 20% off of a top and bottom trimmer if purchased as a pair. Contact us for more information we have 3 to choose from)

 

PISTORIUS MN-200 DOUBLE MITER SAW W/PNEUMATIC HOLD DOWNS

PISTORIUS MN-200 DOUBLE MITER SAW W/PNEUMATIC HOLD DOWNS $3,000

These have and will always be workhorses! This one is powered by dual Baldor saw duty  1.5HP, 230/460V, 3,450RPM Motors. Features dual pneumatic hold downs. 12″ blade diameter capacity. 5/8″ diameter belt driven saw arbors. Foot pedal operation. Scrap discharges to the bottom of the machine. Air filter, regulator, lubricator. Magnetic push button starters. Also includes a pneumatic part/cycle counter.

UNIQUE 250 RAISED PANEL DOOR MACHINE

UNIQUE 250 RAISED PANEL DOOR MACHINE $11,500

We “tuned” this one up and it is ready to go back to work. We replaced all 10 bearings on the sliding carriage, every pneumatic piston (7 total), plus we replaced various air fittings and air lines. Completes square and arched doors in less than two minutes. 7-1/2 HP motor (wired 230V/3 Phase) 50″ cut length with 1-1/4″ spindle; (3) cutterheads on stackable spindle.  Quick change turret for preset cutter height. Pneumatic spindle and material stop positioning. X/Y sliding table for safety & accuracy. Includes, 1 set insert tooling (3 carbide cutters with inserts for cope, rail and panel).  Machine weighs 1,375 lbs. This fully functional machine has been fully cleaned, checked, and is ready to work from the time you receive it.

DODDS GP-26F UNIVERSAL DOVETAIL DRAWER GLUER

DODDS GP-26F UNIVERSAL DOVETAIL DRAWER GLUER $3,000

This clean dovetail gluer applies a precise amount of glue to the dovetail tenons through the use of metering pumps. The amount of glue applied is adjustable so there is no squeeze out when the drawer is assembled saving time in the assembly process. It is designed for materiel up to 28″ in width but will lock and can be used with widths up to 31″. This fully functional machine has been fully cleaned, checked, and is ready to work from the time you receive it.

  • Automatic glue system cleaning
  • No tools required for set-up
  • Fast, precise operation
  • Large glue tank capacity
  • Precise metering glue pumps

DODDS C-36 DOVETAIL DRAWER CLAMP

DODDS C-36 DOVETAIL DRAWER CLAMP $5,500

Model C-36 clamps five-piece drawer design with standard English (finger type) dovetails as well as bored and doweled drawers. The C-36 features almost zero set up time using no tools. The full pneumatic capability range clamp pads require no set-up. This fully functional machine has been fully cleaned, checked, and is ready to work from the time you receive it.

Features:

No tools needed for set up
Assembles several types of drawer construction
Assembles five piece
Maintain clamping pressure
Fully Pneumatic

SCMI 10S 3 HEAD 43″ WIDE BELT SANDER LOADED

SCMI 10S 3 HEAD 43″ WIDE BELT SANDER LOADED $24,000

This is one loaded, lower use, 3 head sander. The first head is helical grooved metal drum, has a  7″ diameter, and is powered by a 35 hp motor. The second head is helical grooved rubber drum, has a 7″ diameter, is powered by a 24 hp motor, features 2 running speeds, and has an air wand. The third head is combination head with a helical grooved rubber drum, has a 7″ diameter, is powered by a 24 hp motor, features 3 running speeds, and has an air wand.  Following the third head is a dust brush. The feed mat features variable speed from 15-70 FPM, is powered by a 3.5 hp motor, and features a vacuum bed. Other features include auto thickness calibration, digital height read out, digital speed read out, 27″ infeed and outfeed rolls PLUS the heads engage automatically when turned on. Max thickness is 6-1/4″. Max working width is 43″. Feed mat has better than 80% life remaining, the 2nd and 3rd heads have NEWER rubber and are defect free. Platen has NEW felt and graphite. Machine is wired 220V/3 Phase. (display can be set for metric or inches)

RAMCO 36″ SINGLE HEAD WIDEBELT SANDER

RAMCO 36″ SINGLE HEAD WIDEBELT SANDER $6,500

This is a good solid entry level machine that belonged to a technical school. Very well maintained. NEWER conveyor that has never been dressed, NEWER rubber on drum, NEW felt and graphite on the platen. This machines features a 20 hp main motor and 1 hp motor on the feed. 220V/440V/3Phase. Combination head features a 2″ width platen. Machine uses 37″ X 60″ abrasives. 6-1/4″ max. thickness capacity.  This fully functional machine has been fully cleaned, checked, and is ready to work from the time you receive it.

BLACK BROS 8″ TABLE TOP GLUE SPREADER

BLACK BROS 8″ TABLE TOP GLUE SPREADER $900

Clean, well maintained, low use, 8″ table top glue spreader in excellent condition. Features an aluminum corrugated roll, lid, and is powered by a 115V single phase motor. Model: 400 ADH SPRD

LOW HOUR DEKKER 25 HP LIQUID RING VACUUM PUMP

DEKKER 25 HP LIQUID RING VACUUM PUMP $12,000

If you are in need of a high quality, pre-owned, vaccum pump this one has everything going for it. It is very clean, only has 3,537 original hours on it, and has just had it’s Vmaxol Oil changed. This pump is capable of 410 CFM and is currently wired 230V/3 Phase. This fully functional machine has been fully cleaned, checked, and is ready to work from the time you receive it.

2000 MIGHTY VIPER V-1600 VERTICAL MACHINING CENTER

2000 Mighty Viper V-1600 Box Way Vertical Machining Center with Mitsubishi KSW-980A CNC Control. $25,000 
(for the entire package tooling & vises/or you minus the tooling/vises for a $2,500 credit)
  
This is our personal machine that we have used with out issue. We are selling to upgrade to an even larger machine. This large
C-Frame Vertical Machining Center shows under 8,000 hours of use.  Since this is our personal machine it can be seen powered
up at our location in Naperville, IL.

Speciifications:

Machine Table Length 67"
Machine Table Width  30 "
Taper: Cat 50 Taper
Direct Drive Spindle Drive
All Box Way Slides Top Condition
Heavy Duty Arm Type Tool changer

Machine Axis Travels
X Axis : 63 "
Y: Axis  31 "
Z: Axis  24.5"  +  5.9"
Spindle Power 20 HP.
Max. RPM 8000 rpm
Spindle Chiller
Rigid Tapping
Automatic Tool changer 32 ATC
All Available Machine & Control Manuals.
Also includes 40 tool holders, tool cart, and misc tooling along with 4 Kurt vises.

MIKRON AUTOMATIC ROSETTE MACHINE

MIKRON AUTOMATIC ROSETTE MACHINE  $3,000

Fully operational, hopper fed, automatic rosette machine capable of making up to 500 rosettes an hour. It comes with the head, but does not have any inserts. It is powered by a 3hp Baldor 208-230/460V motor that is currently wired 230V.  This fully functional machine has been fully cleaned, checked, and is ready to work from the time you receive it. (minus tooling)

ACCU-SYSTEMS HPJ-7

 

ACCU-SYSTEMS HPJ-7 CNC BORE, GLUE, & DOWEL INSERTER $$$RECENTLY SOLD$$$

Clean, well maintained HPJ-7 vertical horizontal CNC Bore, Glue, & Dowel machine. 2.2kw/220v,/3 Phase/24,000 RPM motor with mechanical digital numeric readouts. Vibratory dowel hopper with one tube. Glue pot. 16″ x 49″ capacity between fences. Table bridge with (4) adjustable pneumatic hold-downs in each position. This fully functional machine has been fully cleaned, checked, and is ready to work from the time you receive it.

2007 BUTFERING 3 HEAD 43″ WIDE BELT SANDER W/815 HOURS

 

2007 BUTFERING 3 HEAD 43″ WIDE BELT SANDER W/816 HOURS $$$RECENTLY SOLD$$$

This is a small shop owned machine that was well maintained. It also only has 816 total hours of run time. The First head is a spiral steel contact drum, the second head is a helical grooved rubber contact drum, and the third a combination head with a helical grooved rubber contact drum and an air bladder platen. The inside of this sander is cleaner than the outside……..really! All of the heads are defect free as well as the conveyor. This machine also feature variable speed, digital height read out, as well is auto calibration. You also get a full set of manuals PLUS a pneumatic blast gate that turns on with the machine and a custom dust manifold. This fully functional machine has been fully cleaned, checked, and is ready to work from the time you receive it.

  • Working width:           1100 mm  ( 43” )
  • Abrasive Belt width:  1090 mm ( 43” )
  • Abrasive Belt length: 1900 mm ( 75” )
  • Workpiece thickness min.:   3 mm ( 1/8” )
  • Workpiece thickness max.:  160 mm ( 6 3/8” )
  • Variable conveyor speed:  8 – 42 FPM
  • Feed motor:       1 HP
  • Head #1 = Contact Roller       20 HP
  • Head #2 = Contact Roller      20 HP 60 fps belt speed
  • Head #3 = Combination        18 HP 40 fps belt speed
  • Dust collection requirements:    3200 CFM
  • Dust outlet –  head #1:  160 mm ( 6.25 ” )
  • Dust outlet –  head #2:  160 mm ( 6.25 ” )
  • Dust outlet –  head #3:  160 mm ( 6.25 ” )
  • Compressed air requirements:  90 PSI
  • Air consumption per cycle:          4 CFM

MAY COATING TECHNOLOGIES 450 lb/hr HOT MELT DISPENSER DRUM UNLOADER

MAY COATING TECHNOLOGIES 450 lb/hr HOT MELT DISPENSER DRUM UNLOADER $20,000

We pulled this Acumeter Technologies/May Coating Technologies model  400 DG MCE off a Black Bros line that we recently sold. This is a fully operational hot melt dispenser drum unloader built in 2006. Very hard to find on the used market.  It is capable of delivery rates up to 450lb/hr- depending on the rheology of the material. It is designed to completely empty the contents of 55 gallon drums of hot melt. It can process chicklets, bricks, pellets or granular in addition to 55 gallon drums. Built in reservoir provides non-stop delivery of the hot melt to the application process. Multiple heat zones to deliver the adhesive at optimum application temperature an minimize thermal degradation. Includes a 20′ delivery hose.

GANNOMAT SELEKTA 252N DOWEL INSERTER

GANNOMAT SELEKTA 252N DOWEL INSERTER $3,500

Gannomat Selekta 252, which automatically selects dowels, rejecting those of improper size, applies precise glue amounts and inserts the dowels via a handheld pistol. The Selekta 252 uses a closed glue system requiring no routine maintenance, only occasional rinsing, and features electronic PLC operation.

Dowel diameter: 6, 8, 10 or 12 mm (video shows machines using 8 mm X 25 mm dowels)
Dowel Length: 20 – 50 mm
Working Capacity: 45 dowels per min.
Electical supply: 110 V, 1 PH, 60 Hz
Required Air pressure: 6 bar
Weight: 240 lbs.
Space requirement: 26 in. x 26 in. x 44 in high

– Dowel feeding by maintenance-free vibrator.
– Mechanical system of dowel selection for dowel diameter and dowel length
– Controlled by electronic limit switches with immediate error indication of incorrect dowel length immediate ejection of the defective dowel by pressing the error light button.
– Selector switch regulates glue amount by means of an electronically controlled timer for working with different dowel sizes.

JETRIX 2030 FRK UV FLATBED PRINTER

2013 JETRIX 2030 FRK UV FLATBED PRINTER W/ ROLL FEED, WHITE, PRIMER, LIGHT CYAN & MAGENTA $50,000

This low use, well maintained, 2030 FRK was manufactured in 2013 and also features a 64″ roll to roll feed giving this printer a huge variety of applications. It has an 80-3/4″ X 120-1/2″ over sized vacuum bed (w/3 zones and 3 vacuum pumps) and features 8 colors. Cyan, Magenta, Yellow, Black, White, Primer, Light Cyan, & Light Magenta. The Primer gives the capability to print onto almost any substrate, such as Glass and Stainless Steel. The 2030 FRK also features a PC controller that is very user friendly! Point and click literally! It is running version Jetrix V2.5/2030 operating software. Machine is currently under power and being cycled multiple times weekly. The Jetrix 2030FRK UV Flatbed one of the fastest flatbed printers in the Jetrix range giving a production speed of 55sqm per hour. Producing stunning graphics at amazing speeds. The incredibly functional and easy to use unique Jetrix operating system powers the Konica Minolta heads accurately allowing printing text down to 2pts. This is combined with InkTec’s world-class tailor made UV ink which is vibrant, durable, long-lasting and economical. Machine is currently under power and being cycled multiple times weekly.

  • 14 Picoliter: 1024 nozzles
  • True flatbed capability capability: Print heavy, non-square objects
  • Roll printing system up to 1.6 metres: Vinyl, mesh, textiles, paper, canvas, etc
  • Anti-head crash system: Safety & no loss of printing job.
  • Intelligent vacuum table system
  • White, varnish, Primer: Total printing solution supplies
  • Size: Stationary flatbed: 2050 x 3060mm, Roll: 1620mm
  • Speed: 55 sqm/hr (production mode)
  • Colours: CMYK, LC, LM & White, PLUS Primer option

JETRIX 2513 FQ UV FLATBED PRINTER

JETRIX 2513 FQ UV FLATBED PRINTER W/ WHITE, PRIMER, & VARNISH OPTIONS $30,000

This 2513 FQ was manufactured on 11/11/2011. It has a 4′ X 8′ over sized vacuum bed and has 8 colors including cleaning solution. Cyan, Magenta, Yellow, Black, White, Primer, Varnish, & Cleaner. The Varnish provides a gloss finish for a variety of applications, including fine art and photographic work. The Primer gives the capability to print onto almost any substrate, such as Glass and Stainless Steel. The 2513 FQ also features a PC controller that is very user friendly! Point and click literally! It is running version Jetrix V3.3 operating software. Machine is currently under power (220V/Single Phase) and being cycled multiple times weekly. The over-size flatbed is capable of taking 2m x 3m boards and printing edge-to-edge, perfect for large jobs.

  • True grayscale (from 10 to 30 picoliters): Highest image quality with less ink
  • True flatbed capability capability: Print heavy, non-square objects
  • Prints on Vinyl, mesh, textiles, paper, canvas, etc
  • Anti-head crash system: Safety & no loss of printing job.
  • Intelligent vaccum table system: Media alignment bar. Easy to use
  • Features optional white, varnish, & primer
  • Size: Stationary flatbed: 2440 x 1220mm
  • Speed: 30 sqm/hr (production mode)
  • Colours: Basic: CMYK & White, Varnish, Primer

The 2513 uses the industry-leading Spectra Q-class print head which is able to print down to 2 point text and stunning photographic quality images. It is also extremely economic, meaning the ink cost per SQM is only £0.40 for a full colour and full coverage print. The print head very durable too, on average used a Q-class head is anticipated to last around 3-5 years in the Jetrix. The printer is robust and able to take up to 500kg in weight on the specially designed honey comb bed. It can also print objects up to 10cm in height so is ideal for non-standard bulky items. The Jetrix 2513 features a zonal vacuum system with 3 powerful ring blowers inside, which means the suction can be zoned to the specified print area. This enables solid and accurate positioning of substrates and therefore less wasted media due to reprints plus no more masking the bed off, which is extremely time consuming.

POLYTHERM 3000-5 VACUUM THERMOFORMER (OVEN & PRESS)

NORFORD INDUSTRIES POLYTHERM 3000-5 VACUUM THERMOFORMER (OVEN & PRESS) $45,000

An extremely rare find on the used market. These are very heavily built machines that are designed to last. If you are looking at expanding capabilities look no further. Easily shape and bend solid surface, vinyl, and laminate. Can you make a solid surface sink, bowl, shower base, or wrap a contoured counter-top? With the Polytherm 3000-5 you can. Plus you can also use this set up for vinyl and laminate as well.

This system comes with a 41″ X 152″ three zone/six thermostat (for control and uniform heat) heated platen press that heats from both the top and bottom to eliminate cold spots and a 49″ X 165″ vacuum membrane press with a 3 hp Busch vacuum pump. The 49″ X 165″ measurement represents inside usable vacuum field.  The press is 182″ X 66″.  Both units are in full working order, well maintained, and have low hours.

  • Increased fabrication
  • Design innovation and flexibility
  • Multifunctional
  • Low maintenance
  • Easy to operate
  • Reduction in waste
  • Reduction in process time
  • Seamless finish
  • No dust extraction required
  • No special installation required
  • Lower operating costs

RFS 36″ X 60″ RADIO FREQUENCY GLUER

RFS 36″ X 60″ RADIO FREQUENCY GLUER $12,500

Small shop owned, well cared for, and low hours (5,323 total hours) means a tremendous value. Fully operational and in excellent condition this RFS SL48N6A has a 36″ X 60″ X 2″ capacity. Clamping pressure is applied by multi-power pneumatic cylinders to maximize pressure while relying on standard plant pressures. Edge pressure is applied by eight (8) each pusher shoes, each with a 4” bore x 4” (100 x 100 mm) stroke twin-piston multi-power pneumatic cylinders. Top platen pressure is applied by two (2) 5” diameter x 16” (125 x 406 mm) stroke pneumatic cylinders that keeps the footprint to a minimum while still allowing the operator full access to the platen area. This machine is in excellent condition both mechanically, cosmetically, inside, and out.

ARCHER 100 HP BLOWER

ARCHER 100 HP BLOWER $3,600

This blower runs off a newer (2006) Toshiba 100 HP motor. The inlet measures 33″ and the outlet measures 26″ X 29″. The fan has a diameter of 56″ and the housing approximately 76″.

MIDWEST AUTOMATION 5033 COUNTER TOP SAW

MIDWEST AUTOMATION 5033 COUTERTOP SAW $5,500

Midwest Automation 5033 in good operating condition. Integrates cutting off and/or mitering self edged tops, postformed coved tops, or solid surface countertops, making both a mitering cut and draw bolt mortises in one simple cycle. Equipped with a 5 HP belted drive saw motor, 16″ diameter blade, and 1″ diameter arbor. Includes four 1.5 HP high speed router motors for routing the draw bolt mortises. 1/2 HP variable speed DC traverse feed motor. 4 Pneumatic hold downs. Upper machine structure rotates to the left and right to (5) fixed stops at miter positions: 90°, 45° right and left, 22-1/2° right and left. Specifications: 5-5/8″ depth of cut with build-down (4-7/8″ with out build-down); ¾” maximum build-down thickness, 4-7/8″ maximum back splash height, 42″ crosscut capacity at 90°, 38″ at 22-1/2°, 39″ at 45°.

AMERICAN FINISHING SYSTEMS 8 HEAD SANDER

AMERICAN FINISHING SYSTEMS 8 HEAD LINEAR BRUSH PROFILE SANDER $17,500

This Lineal Profile Sander/Polisher is designed to perform a wide variety of surface treatments on mouldings, slats, wood, or plastic parts, with virtually no change to the moulded profile. Typical uses include: sealer sanding, base coat sanding, de-nibbing, or polishing between coats, as well as high gloss polishing, and buffing. It can also be used for bare wood sanding to improve finishing. In some situations, it can remove knife marks, but it is not specifically designed, or guaranteed to remove them. 4 top and 4 side heads with a 6-1/2″ width capacity. All heads are SlipCons and feature variable speed plus forward and reverse. Top heads with 30 degree tilt, electronic variable speed w/reverse factory range 0-3400 RPM) Side headsElectronic variable speed w/reverse (factory range 0-3400 RPM). Sanding Spindles 1-1/4” O.D., heat Treated, stress- relieved steel. Non-threaded for quick changeover of abrasives. Precise vernier screw type adjustments of sanding heads. Powered roller thru-feed workbed Variable Speed control Factory range 0-300 FPM. Fixed Roller Guide Back Fence. Adjustable Roller Guide Front Fence. Top Pressure Hold-Down units. Machine is currently wired 230V/3 Phase. This fully functional machine has been fully cleaned, checked, and is ready to work from the time you receive it. 

WEGOMA MPA-2 CORNER CLEANER

WEGOMA MPA-2 CORNER CLEANER $3,000

Dual head corner cleaner in good operating condition. We replaced and/or rebuilt 5 air cylinders in total to guarantee it is in good operating condition. Currently wired 230V/3 Phase. 2 sets of tooling included. In above average condition considering other MPA-2’s out there.

TRISTATE 36″ RESAW

TRISTATE 36″ RESAW $12,500

This is a very well maintained model T3642 resaw featuring a 25 hp main motor and variable feed speed. Feed speed varies from 10 to 250 FPM. 36” X  3-1/4″ drive wheels.  Approximately 14” of vertical capacity and a 10″ of horizontal capacity. Table tilts up to 45 degrees. Spring loaded blade tensioning. Bottom blade cover, riser blocks, and adjustment wrench included. Machine shows moderate to low use for it’s age and is a real gem.

CTD N80 DOUBLE MITER & TOE KICK SAW

CTD N80 DOUBLE MITER & TOE KICK SAW $3,800

Notice that we said double miter “and” toe kick saw. Our customer purchased this as a double miter saw and didn’t use it that much. He then purchased the parts to convert it to a toe kick saw and didn’t use it that much. He then sold it to us to clear shop space. Very solid, clean machine that has no issues. Dual Baldor 2 hp 208-230/460V/3 Phase motors currently wired 230V/3 Phase. Foot pedal operation.  This heavy duty machine can have blades set for notching or mitering. Blades move vertically on linear bearings on 1″ (25mm) hardened and ground rods. Keyed fences allow for each set-up and accurate dimensional changes. This fully functional machine has been fully cleaned, checked, and is ready to work from the time you receive it.

MILLER MOORHEAD 31″ MODEL 310 LAMINATE SLITTER W/ NEW CUTTERS

MILLER MOORHEAD 31″ MODEL 310 LAMINATE SLITTER W/ NEW CUTTERS $3,200

These are heavily built machines that will last several lifetimes. Single phase (115V) multi speed operation. 31″ capacity. NEW set of cutters installed so the cut is as good as it gets! This fully functional machine has been fully cleaned, checked, and is ready to work from the time you receive it.

LARGE CAPACITY RAMARCH PNR9 4 SIDED ROTATING CLAMP

RAMARCH PNR9 4 SIDED ROTATING CLAMP $15,000

A very rare find in North America…….because these are pretty pricey new! Luckily this one is pre-owned and in very good condition. Not to mention the fact that it comes with 39 clamps. Basically each side/face has 3 sides with squaring channel that is 3-7/8″ deep. The capacity between this channel is 137″ wide X 56″ tall. You can use this space to clamp one large work-piece and consider this a “4 zone clamp” OR you can split the 137″ to whatever dimension you want and create up to “8 zones.” You can do this because on each side you have 2 pairs of pneumatic controls. Meaning one pair per side for the vertical clamps and one pair for the horizontal clamps. Meaning 4 total pairs per side for a total of 16 controls so you can have flexibility in how you set up the clamp. They are also separated out in pairs to the left and right of the clamp. Further more the carousel is spun via a hydraulic brake motor which allows you to stop the carousel at any angle for operator comfort. This fully functional machine has been fully cleaned, checked, and is ready to work from the time you receive it.

QUICKWOOD PRO 1100 44″ BRUSH SANDER

QUICKWOOD PRO 1100 44″ BRUSH SANDER $$$RECENTLY SOLD$$$

Another, CLEAN, low use machine brought to you by 360 Degree Machinery. De-nibbing sander models PRO are a rotary type sander designed for finish sanding and de-nibbing of raw wood components and sealer sanding of stained and sealed parts. The PRO series of sanders are designed to handle three dimensional work pieces or items with profiles, raised panels, flat doors, drawer fronts, or moldings made from either MDF or hardwood. The model 1100 has 15 inch long spindles with a 43.5 inch wide conveyor. The PRO model sanders are designed with high volume high quality component finishing as a standard. Can be used with mouldings, drawer fronts, raised and flat panel doors, hardwood, MDF……ect. Equipped with a rotating carousel driven by a 1.5 HP motor. Carousel rotation speed is variable from 4 to 28 RPM. Carousel contains 4 gearheads with 2 spindles each, giving a total of 8 sanding heads. Both carousel and heads feature forward and reverse. The 4 gear-heads are each driven by an individual 2 HP motor. Spindle speeds are adjustable from 200 to 1200 RPM. Vacuum hold down system is powered by a 15 HP motor. Total HP 27.5 HP. 4-1/4″ thickness capacity to the bottom of the brushes. This fully functional machine has been fully cleaned, checked, and is ready to work from the time you receive it.

QUINCY QSB SERIES 50 HP ROTARY SCREW COMPRESSOR

 

QUINCY QSB SERIES 50 HP ROTARY SCREW COMPRESSOR $4,800

Clean rotary screw compressor with 12,444 hours from a brand you can trust. Capable of 235 CFM @ 100 PSI, 206 CFM @ 125 PSI, or 187 CFM @150 PSI. We believe it is a 2004 model year and yes, that is the original paint.

UNIQUE 4512 SHAPE AND SAND

UNIQUE 4512 SHAPE AND SAND $$$RECENTLY SOLD$$$

This particular machine was used very sparingly and is extremely clean. Machine features  (3) Stations total (w/jump cope)– (1) floating shaper and (2) floating sanders each with 5″ stack capacity. Shaper station is a 10 HP direct drive motor with 1-1/4″ diameter arbors. Shaper station has variable speed from 6,000 to 9,000 RPM and is reversible. (2) Sanding stations are 2 HP direct drive Baldor motors with 1″ diameter arbors. Sanding stations are variable speed from 6,000 to 9,000 RPM and reversible.  Variable speed conveyor speed from 0 to 35 FPM. 6″ heavy duty conveyor and roller hold-down system. Sanding stations tilt 45° and have air jets. Maximum material thickness – 2-1/2″; minimum material width – 1-1/2″ plus the depth of the cut. (1) 5″ Diameter dust port and (2) 4″ diameter dust ports

DEWALT MODEL GE 16″ SINGLE PHASE RADIAL ARM SAW

DEWALT MODEL GE 16″ SINGLE PHASE RADIAL ARM SAW $900

This 16″ blade capacity radial arm saw is driven by a 230V/single phase 5 hp motor.

PISTORIUS SC12 CUT OFF SAW W/ FENCE

PISTORIUS SC12 CUT OFF SAW W/ FENCE $2,000

This is a Pistorius model SC-12-PRH cut off saw. 12″ blade capacity. 3 hp 230/460V/3 Phase motor currently wired 230V. 8′ locking jaw-stop style fence with scale.

UNIQUE NO. 73 DUAL SPINDLE POCKET SCREW MACHINE

UNIQUE NO. 73 DUAL SPINDLE POCKET SCREW MACHINE  $2,400

Dual spindle drill tub with 1-1/8″ centers. Insert your work piece, push the palm button, and the machine will clamp and drill 2 pocket holes in one operation. Machine uses single phase 120v power. Good, solid, strong running machine.

2000 DIEHL SL50RBD STRAIGHT LINE RIP SAW 4-1/4″ THICKNESS CAPACITY

2000 DIEHL SL50RBD STRAIGHT LINE RIP SAW 4-1/4″ THICKNESS CAPACITY $$$SOLD$$$

We can easily rate this machine as being in Excellent ++++ condition. It would also be nearly impossible to duplicate this machine. It is smooth and quiet running from it’s lowest to it’s highest feed rate. The chain face is in near mint condition and SHARP (see photos) and the chain sits dead flat. We would easily rate this chain a 9.5 out of 10. Meaning if you want better you would have to buy a new one. Not only is this machine in mechanically excellent condition, but we would also rate it in excellent cosmetic condition. It also boasts the latest in safety features with the newest style of top (triple finger) anti-kick back fingers along with a lower front set that use a sonic sensor and or touch to deploy. Pneumatic brake on the main motor. Maximum depth of cut with an 18” blade is 4-1/4”. 2” diameter saw arbor. 15 hp, 220/440 volt three phase direct drive saw arbor motor (currently wired 220V/3 Phase). Adjustable feed speeds of 55 to 200 ft/min. Throat depth to right of blade 25”. Minimum part length 10”. Minimum thickness .125″. Max thickness 4-1/4″. Table right of saw blade 19″. Table left of saw blade 30″. 57” wide x 79” long machine work table. 35” table work height. Adjustable in-feed table rip fence. Adjustable top pressure beam with (8) spring loaded rollers…..and yes all the rollers spin freely and do not have flat spots on them. Automatic pneumatic chain lubrication system that works as it should at all points. Front push button motor controls. Machine weight 4250 lbs.

(2) DODDS SE-25 DOVETAIL MACHINES

(2) DODDS SE-25 DOVETAIL MACHINES $$$RECENTLY SOLD$$$

This is something you don’t see very often a pair of Dodds 25 spindle dovetail machines. One is set up for males and the other is set up for females. Each machine has a new set of 3/8″ tooling for a total of 50 new bits on 1″ centers with a total maximum width capacity of 25″. 5hp 220/440v drive motor ,1/2hp; 220/440v stroke motor. Pneumatic clamping of material Foot pedal control with choice of either manual and automatic mode. Auto-mist lubrication.

BLACK BROS 4 X 8 END LOAD COLD PRESS W/ MOTORIZED OPENING

BLACK BROS 4 X 8 END LOAD COLD PRESS W/ MOTORIZED OPENING $$$RECENTLY SOLD BUT WE DO HAVE A 5’X10′ COMING SOON$$$

This 4′ X 8′ (50-1/2″ x 98″ actual) end load cold press features a motorized height adjustment with a max opening of  46″. Bottom rollers spring retract automatically when material is pressed. Automatic material thickness rod stops machine from lowering when it hits the proper lowered height. The platens are smooth, flat, and do not have dents.

TIMESAVERS 36″ PLANER SANDER W/HELICAL HEAD/ 1,636 HOURS

TIMESAVERS 36″ PLANER SANDER W/HELICAL HEAD/ 1,636 HOURS $$$RECENTLY SOLD$$$

This machine came in on trade and only has 1,636 hours on it. The first head is a 30 hp helical planer head with 9 rows and 300 inserts. We cleaned and serviced the head and replaced all 300 carbide inserts. They are 4 sided and we are told that you can expect to produce around 150,000 board ft per turn. The second head is a 20 hp combination head featuring a 5″ helical grooved rubber head with platen. We dressed the drum and it is defect and memory free. Grooves are deep and we would estimate it to have at least 80% life left in it. The machines comes with 2 platens, one installed in the machine and a second one as well (different felt densities). We replaced graphite on both and the felt on one. We also upgraded the feed mat to a brown nitrile rough top belt. It offers better grip which equates to a better finish of your product when it exits the machine. This machines also features digital thickness read out and control along with auto thickness calibration. PLEASE NOTE: We are not selling you a machine just pulled from a shop, but a machine ready to be put back to work.  All the critical and expensive consumable parts of this machine have been serviced or replaced as they should be when you purchase a used machine. This fully functional machine has been fully cleaned and checked and is ready to work from the time you receive it.

Series 2300 specifications:

First head 30 hp

Second Head 20 hp

Centralized control panel

Digital thickness readout

Double infeed and outfeed holddown rolls

Hour meter (indicating 1,636 hours)

Main motor load meters/Watt meters

Four bed jacks

Infeed stop bar

Drums and combination head types standard

Dial indicators on drums/platens

5-1/2″ diameter  combination head)

2 1/2″ width platen on combination head

75″ abrasive belt length

Disc brakes on main motor

20-45 FPM feed speed A/C

Auto set-up device

Motorized lift

0-4.5″ opening (33-38″ passline)

14″ infeed loading area

Through-beam abrasive belt tracking

15″ minimum part length

2005 BUSELLATO JET 260 DUAL 4′ X 10′ CNC MACHINE W/C AXIS

 

2005 BUSELLATO JET 260 DUAL 4′ X 10′ CNC MACHINE W/C AXIS  $$$RECENTLY SOLD$$$

This is a rare machine. On the left is a 4′ X 10′ flatbed complete with rake, offload table, and it’s own Dekker 25 hp vacuum pump reading 3,505 hours and directly to the right is a 4′ X 9′ pod and rail machine complete with auto pod positioning (via aggregate head/included) and it’s own 5 hp vacuum pump. Complete with chip conveyor, saw aggregate, manuals, parts, accessories, spare pod covers, and safety fence per pictures.  This machine offers a lot of flexibility!!!

X Axis: 236″
Router Table Length: 120.1″
Pod and Rail Table Length: 110.2″
Y Axis: 53″
Max Panel Thickness: 3.94″
Total X Axis Stroke: 256.4″ (router table length 122″/Pod & Rail length 110.2″)
Total Y Axis Stroke: 63.8″
Total Z Axis Stroke: 8.1″
Max X Axis Positioning Speed: 70mt/min
Max Y Axis Positioning Speed: 50mt/min
Max Z Axis Positioning Speed: 15mt/min
Operating Pressure: 6 bar/90 PSI
Dust Hood Diamter: 250mm or 9.84252″
MFT Panel Supports: 6
19 total spindles & saw head
X Axis Spindles: 11
Y Axis Spindles: 8
Router Spindle: 12 HP
Rotation Speed: 1000-18000 RPM
Tool Attachment: HSK F63 cone
Tool Position: 15 (rotary style)
Unloading Table: 9′
Pod & Rail Vacuum Pump: 5 Hp vane pump
Main Vacuum Pump: 25 HP

BOSS DSP-610A TOP & BOTTOM 24″ HELICAL HEAD PLANER

BOSS DSP-610A TOP & BOTTOM 24″ HELICAL HEAD PLANER $$$RECENTLY SOLD$$$

This exact planer is offered under several names and is a proven design that has been around for around 25 years. It has a 24″ width capacity and a generous 8″ thickness capacity. 20 hp motor on the top head, 15 hp motor on the bottom, 3 hp on the feed, and 1/2 hp motor for the raise and fall of the chrome plated bed. Dual chevron cutter-heads. A chevron is like a helical head but instead of a spiral arrangement of the cutters it has a “V” arrangement. This sends the chips and dust to the center of the cutter-head and up thru the dust chute enabling for more effecient removal of waste. This planer also features an automatic oiler. Digital read out/control for height. An extremely clean double sided planer that has been very well maintained.

Features:
  • Upper & lower chevron (like helical) cutterheads for accurate and powerful two-sided planing in one pass.
  • auto digital thickness control for quick and accurate setup.
  • The work table surface was precision ground and then electro chrome plated and polished to a smooth mirror finish. The durable wear resistance surface is easy to clean and maintain.
  • A heavy duty feed conveyor with metal spikes firmly holds stock securely to the work table and feeds positively giving a smooth finish for rough or final planning.
  • A stepless variable speed control for smooth adjustment of feed rate depending on the material hardness, depth of cut & width to provide the best finish surface and fast cutting performance.
  • The infeed conveyor is fitted with numerous pressure pins so the feeding process can be firmly stabilized. It will moderately press the stock, and then accurate planing surface can be performed to prevent jumping during processing of narrow or bent material.
  • The 4 power feed rollers are driven with a geared transmission box linked with heavy-duty drive chain and gears to provide a smooth even feeding during rough or finish planing.
  • The heavy duty rigid cast iron frame supports the work table and helps dampen vibration and ensures years of dependable service.
  • Powerful industrial motor for maximum cutting capacity.
  • All precision sealed long-life bearing for durability usage.
  • Changing the Carbide inserts on the upper cutterhead only requires removal of the upper dust chute; the top cutterhead inserts can then easily be changed.
  • The spiral insert heads design allows for fast accurate insert changes & minimum down time.
  • Setup time is minimized to set cutterhead height using the auto material thickness device.
  • The top and bottom cutterheads are precision balanced to provide consistently smooth chatter free planing regardless of the feed rate or hardness of material being planed.
  • A powerful ½ HP motor is utilized to quickly & conveniently make adjustments in thickness when setting the upper cutterhead.

 

 

 

KVAL 950-3 AUTO HINGE JAMB ROUTER

KVAL 950-3 AUTO HINGE JAMB ROUTER $6,500

Fully operational 950-3 set up to do 5/8″ radius hinges. Capable of 8 jambs a minute. Will do all 3 hinges on a 7′ jamb in one cycle, but we are told it will do longer jambs but requires a second cycle/set up for longer jambs. 115V/Single phase operation over air. This fully functional machine has been fully cleaned and checked and is ready to work from the time you receive it.

KVAL 960-3 AUTOMATIC STRIKE JAMB ROUTER

 

KVAL 960-3 AUTOMATIC STRIKE JAMB ROUTER $6,000

This fully functional machine has been fully cleaned and checked and is ready to work from the time you receive it. Over all in very good to excellent condition.

Using the KVAL 960-3 Automatic Strike Jamb Router, a fast operator can machine 5 jambs per minute with a full lip strike routing pattern. The 960-3 features a fully automatic machine cycle that includes clamp-up and ejection.

The 960-3 is designed so that router movements are fully automatic. The router moves in a rectangular pattern for face plate and then moves in to route for the deeper latch hole. Both flat jambs with stop, as well as split jambs, can be accommodated. Jambs are placed against either a right-hand or left-hand indexing stop and are clamped firmly into position at the touch of a foot pedal.

Electrical requirements 110V/Single Phase

TAYLOR 20 SECTION AUTOMATIC CLAMP CARRIER

TAYLOR 20 SECTION AUTOMATIC CLAMP CARRIER $$$Recently SOLD$$$

The best way to describe this clamp is clean with low use. It has had a soft life and was meticulously maintained and cleaned after every use. Simply put this is the cleanest Taylor on the market.  Taylor’s are made to run 3 shifts and take abuse, but after time they begin to show signs of heavy use. Especially if run 8, 16, or 24 hours a day 5 days a week. This particular machine has had a soft life and was used several hours a week. In the last 6 years it has seen almost no use. Yes, that is the original paint and the machine is in excellent condition from top to bottom. All 120 clamps function as they should. They are straight, all the screws are tight and thick threaded and none are stripped or worn. Every spring is present and functions properly on all 120 clamps. This machine doesn’t have a single air leak. To top it off this machine has been completely cleaned and detailed and is ready to work from day one guaranteed! This particular clamp has an 8-1/2′ X 32″ capacity with the back plates being 2-1/2″ deep. It comes complete with safety eye, manual, 48″ pneumatic plate glue spreader, spare parts, and even a barrel holder/flipper for glue. If you are looking for a 20 section automatic Taylor there is no need to look any further as this one is as clean as one can get and ready to go. This machine shows how when you buy with 360 Degree Machinery we are “Helping you buy with confidence.”

PISTORIUS MN-200 DOUBLE MITER SAW

PISTORIUS MN-200 DOUBLE MITER SAW $2,900

This machine is fully operational and in over all good condition. 8′ infeed and outfeed tables. One includes locking jaw-stop and scale. Dual 1-1/2 hp saw duty motors. 12″ blade diameter with 5/8″ arbors. 2-5/8″ Max. height &  3-3/8″ max. width capacity. Air actuated and foot pedal controlled.

DIEHL SL-55 STRAIGHT LINE RIP SAW

 

DIEHL SL-55 STRAIGHT LINE RIP SAW $10,000

This is a smooth running SL-55 with a good chain, track, and race. We replaced the entire spindle assembly, including the inner arbor sleeve, and both C2 bearings. Yes, you read that correctly Diehl uses C2 precision bearings. 15 HP Direct drive arbor motor with a  2 HP Feed motor featuring 55 or 110 FPM.  2″ Diameter arbor with a 16″ Maximum blade capacity and a 2-1/2″ maximum depth of cut with a 16” diameter blade, 1-1/2” maximum depth of cut with a 14” diameter blade.  Minimum  depth of cut is 1/8″. Twin chain drive – cuts from bottom. Top pressure system with (6) spring loaded pressure rolls. Table size – 56” long x 45” wide. 19″ of clearance to the right of the blade. Table height is 34”. Floor space required – 67” wide x 65” long . Automatic chain lubrication  230/460 Volt 3 phase (currently wired 230V)

NEW JOOS HOT PRESS

NEW JOOS HOT PRESS  Contact us for a quote today!

We have seen a lot of presses. If we had a choice we would buy Joos and Joos alone. We chose Joos because of the stellar service and support Joos USA offers in addition to the the quality of every component on a Joos press. From the quality of the actual steel that makes the frame to the placement of supports. Hi end/no compromise components and engineering can be found through-out their products. You get gold anodized platens and features like their patented ABS that all but eliminates pressing incorrectly loaded or forgotten parts. Did we mention the Elkom platens! You can also choose between glycol/water, electric, or oil heated platens. Electic plates to 425 degrees (working) Fahrenheit,  high pressure plates that can reach 300 degrees Fahrenheit plus or minus 1 degree or oil plates up to 800 degrees.  One thing that is often over looked is the quality of their heaters. They offer the most stable temperatures with the minimum energy consumption. Contact us for a quote today.

IMA HKA / Brandt KTD 820 CONTOUR EDGEBANDER

IMA HKA / Brandt KTD 820 CONTOUR EDGEBANDER $8,900

This is one of those hard to describe machines as it can be used handheld or docked. Designed for straight, curved (contour), or beveled edgebanding. 0.4 – 3 mm Edgebanding thickness, capacity for 3 mm PVC banding, 16 – 42 mm workpiece height, automatic advance of banding material from 2.30 – 13.80 FPM. Small glue pot for quick heat-up, magazine for coil or solid strips, guillotine cutoff, manual advance of panel through glue roller via pods OR large panels can be edgebanded by walking around the top with hand held option. Fully operational with a brand NEW (5/$2,300 value) set of pods. Quiet running, fully functional machine, wih a glue pot that heats up fast, and has been fully cleaned and checked and is ready to work from the time you receive it.

1995 NORTHFIELD 24″ JOINTER

1995 NORTHFIELD 24″ JOINTER $$$SOLD AS IT LISTED$$$

This machine was used sparingly in a pattern shop and is a single owner machine. What also makes it a great find is that it is a 1995 model. It is wearing it’s original paint and has no repairs. It also features a 10 hp 230/460V Reuland motor currently wired 230V. 4 Knife cutter head with electric brake. Tables are dead flat! Is anyone even surprised? This fully functional machine has been fully cleaned and checked and is ready to work from the time you receive it.

CELASCHI PROGRESS 36A SINGLE END PROFILER OR TENONER

CELASCHI PROGRESS 36A SINGLE END PROFILER OR TENONER $9,500

This machine is very clean, amazingly complete, well optioned/loaded, and the hour meter only shows 9326 run hours. It features Four 7.5 kW (10 hp) spindles with 50 mm x 420 mm spindles with vertical & horizontal motorized positioning and 1,000 memory presets. All four spindles feature forward and reverse and the 420mm or 16-17/32″ long spindle will allow for stacked tooling. In addition to these features heads 1 & 3 are jumps! Dual chain tracks one inboard fixed 4-1/2″W with pop-up dogs every 16″ and one outside w/motorized adjustment, 3″ wide with pop-up dogs every 16″. Motorized fence with electronic digital read-out for sizing of product. Also included is a full Oertli tooling package consisting of 29 heads  (pictures of profiles provided in gallery at bottom of this page) and a plethora of inserts. Full sound enclosure, separate control cabinet w/operator panel, foot pedal, hand control pendent, hand set up read out, manuals, and schematic included. (note this is a clearance item and priced accordingly)

CLARY CS10CM DOUBLE MITER SAW

CLARY CS10CM DOUBLE MITER SAW $1,000

Clean, fully functional, 45 degree miter saw. It can be hand or foot operated. There is also a spline station built in front of the 1HP 230/460V/3 Phase saw with built in router. Dual 76″ infeed tables with 4 material stops.

 

CLARY 42″ DOOR ASSEMBLY CLAMP

CLARY 42″ DOOR ASSEMBLY CLAMP $900

Designed to hold component parts of exterior or interior door units in position to facilitate faster, easier, and more accurate assembly. Handles doors up to 7’0″ in height and up to 42″ in width. There are 2 pusher bars, one pushes forward and one backward. Total travel is 42″. In other words you can also clamp two 21″ doors, or a 30″ and a 12″, or two 18″ with room to spare.

BRANDT OPTIMAT F13 TOP & BOTTOM TRIMMER W/END CUT

BRANDT OPTIMAT F13 TOP & BOTTOM TRIMMER W/END CUT $5,000

Clean fully functional top and bottom trimmer (curved or straight) by Brandt. 47″ x 31″ cast aluminum main table with (2 top/bottom) .58 hp cutterhead motors. Side mounted trim saw station with a .5 hp saw motor, and 26″ x 6 1/2″ side table. Top & bottom radius profiled cutter heads w/ insert cutter knives. Separate foot pedal controls for edge trimming & saw stations. 3 mm max edgebanding thickness capacity. 70 mm max distance between top & bottom cutter heads. Turn knob height adjustment of top cutter head. Includes manual. This fully functional machine has been fully cleaned and checked and is ready to work from the time you receive it.

TANNEWITZ XJ 18″ TABLE SAW W/52″ FENCE

TANNEWITZ XJ 18″ TABLE SAW W/52″ FENCE $2,800

The best way to describe this saw is a brute. It will easily accommodate an 18″ blade (can’t lower 100% with an 18″ as it will hit the bottom of the dust chute) With an 18″ blade you can get a 4-1/2″ depth of cut. 5 HP direct drive 230/460V 3,600 RPM Fan cooled motor, 1-1/8″ right tilting arbor  with a 1-piece main table, table size 42″ wide x 44-1/2″ deep (not including side table) Motor was rewound including new bearings on 9/22/2006 by Dreisilker. Base formed from hot-rolled steel of 5/16″ thickness & welded into (1) solid unit; 10″ dia. hand wheels for easy adjustment of tilting, raising & lowering of arbor. Miter gauge is not serial number matching but we were able to hand lap it and it fits very tight and will run in both slots. Throat plate and side extension table are numbers matching. 52″ fence, manual, and a few spare blades included. Please note: No blade guard.

JLT CABINET DOOR & FRAME CLAMP

JLT CABINET DOOR & FRAME CLAMP $5,900

This cabinet door and frame clamp has been fully cleaned and checked. This means that it has a good regulator, no air leaks, the easel raises and lowers as it should, forward reverse switch works as it should,  and that the machine is clean and glue free. Description: Inclined style clamp with 2-way pneumatic pressure (top and side) 51″ x 76″ clamping capacity. Vertical power up/down via single phase 115V motor and ball screw.  Horizontal clamping via 2 pneumatic cylinders and foot pedal actuated. model 78B-CDFC-M7 Replacment cost $15,995

STANDARD FLAP & PNEUMATIC DRUM SANDER

STANDARD FLAP & PNEUMATIC DRUM SANDER $2,750

You get a lot of flexibility when you buy this well kept machine. It can be either a flap sander, a pneumatic drum sander, or both. As there are enough parts to configure it either way. It is powered by a 230V/3 Phase motor. All belts and bearings are in excellent condition. This sander is made by Standard and the model is a 7RSBY. This fully functional machine has been fully cleaned and checked and is ready to work from the time you receive it.

FLETCHER FM-2001 TOP AND BOTTOM TRIMMER

FLETCHER FM-2001 TOP AND BOTTOM TRIMMER $5,000

These are made by Fletcher and were also sold under the Delmac brand for well over a decade. Very well built and this machine can handle 3 mm material! Over head control panel for easy operator access, Non-marring phenolic top, heavy fabricated steel base, polished chrome copy shoes w/ fine adjustment screw for accurate and uniform trimming, trimming motors mounted on linear bearings, upper trimming unit adjusts for 1/2″ to 2-1/4″ thick panels, spring loading for constant pressure, top and bottom 0.7 HP motors that are adjustable from 0-12,000 RPM with inverter drive. Pneumatic cylinder w/foot pedal control for rasing and lowering of upper trim unit. This fully functional machine has been fully cleaned and checked and is ready to work from the time you receive it. Currently wired 230V/3 Phase

 

 

 

 

CTD D22 DOUBLE MITER SAW W/IN/OUTFEED TABLES

CTD D22 DOUBLE MITER SAW W/IN/OUTFEED TABLES $3,400

This fully functional machine has been fully cleaned and checked and is ready to work from the time you receive it. It features a 12″ blade Capacity and a fixed cutting angle of 22.5 degree. Motors are 1.5 hp Baldors and are 115/230V single phase. Dual pneumatic holds downs. In-feed and out-feed tables are 60″.

  • Spindle and Pivot: Both mounted on pre-loaded and sealed ball bearings.
  • Iron Castings: Saw arm, pivot brackets and table are precision machined and ground with milled slots in table to guide pivot brackets and fences.
  • Motors and Voltages:1-1/2 HP single phase 115/230V
  • Table Height: 34-1/2” from floor.
  • Blade Wear and Angular adjustments: Each saw head has adjustments for blade variation. Allows for precision alignment of blades to minimuze scrap. Saw heads are adjustable up to 3 degrees, always assuring perfect mitres.
  • Production Rate: The D22 is capable of cycling at one second intervals. However, actual production rates vary with the type and width of material to be cut
  • Actuation: Pneumatic foot valve with cover
  • Air Pressure: 75 PSI with Air Filter/Regulator/Lubricator; includes Auto Drain.

DELMAC DMG 62CT or FRAVOL AZ/2 TOP & BOTTOM TRIMMER

DELMAC DMG 62CT or FRAVOL AZ/2 TOP & BOTTOM TRIMMER $3,500

This is a low use Italian made Fravol AZ/2 top and bottom trimmer distributed by Delmac in North America as a DMG 62CT. Mechanically it is in excellent plus condition. It’s only downfall is that it has scratches on the case as the previous owner moved it around when he needed it. It has dual .7hp motors on floating heads and is capable of trimming up to 3mm material. The motors are high speed spindles running up to 12,000 rpm and are run on single phase 220V power. Heads are foot pedal activated. SPECS: Shaft diameter-16mm, Shaft height-50mm, Mininmum inside trimming radius-20mm (3/4″), Panel thickness min/max 5/8″- 2 1/4″, Table top size-25 1/2″- 39 1/2″.

KARL ENGELHART TWF 1000 STAIR TRENCHER AND MULTI BORING MACHINE

KARL ENGELHART TWF 1000 $2,500

A rare machine in North America mostly due to cost. At over $30,000 NEW it’s not hard to see why so few made it to this part of the world. Like most German made machines this one is well thought out,  accurate and precise. This well cared for machine’s motion is effertless and flawless. With nearly 62″ of x-axis travel, 48″ between rails from front spindle, 54″ from the back,  3 1/2″ of y-axis travel, and 3 1/8″ of z-axis travel this machine can do things few boring machines can. It also has the ability to bore open ended at the end of the machine. The clamping rails have rubber inserts across the top so that your work piece does not get damaged. The clamping capacity is a generous 4 1/2″ and fully adjustable. Power is provided by a 220V/3 phase 4 hp motor that has 2 speeds plus forward and reverse. Twin spindles turn counter clockwise one another and are flat belt driven. With a built in halogen work light, squaring fence, and built in castors it’s not hard to see the German engeering. Use it to trench stairs, cut slots, dados, bore holes…..lot’s of possibilities…..