WEINIG UNIMAT STAR 1000 MOULDER 8,000 RPM W/950 GRINDER + TOOLING $65,000

WEINIG UNIMAT STAR 1000 MOULDER 8,000 RPM W/950 GRINDER + TOOLING $65,000 This moulder has everything going for it. From how well maintained and clean it is to it’s completeness. It also shows low usage for a 1000! B-R-L-T-T-B 8,000 RPM spindle configuration, beautiful bed plates, Rondamat 950 Grinder, Weinig Memory System, Manuals for everything, […]

Read More →

BLACK BROS SIDE LOADING 5’X10′ ADJUSTABLE OPENING COLD PRESS $30,000

BLACK BROS SIDE LOADING 5’X10′ ADJUSTABLE OPENING COLD PRESS $30,000 This side loading Black Bros cold press features a 5′ X 10′ (62″ X 122″ actual) capacity with a 40″ motorized daylight opening. The top is comprised of 3 plates. One 24″ plate to the left and twin 48″ plates to the right. They can […]

Read More →

2013 HOLZ-HER ARCUS 1334 EDGEBANDER W/2,600 HOURS $67,500

2013 HOLZ-HER ARCUS 1334 EDGEBANDER W/2,600 HOURS PRE-MILL CORNER ROUNDING $67,500 Clean loaded Holz-her 1334 with all the options like pre-mill and 4 motor corner rounding. Machine currently has a little over 2,600 run hours on it. Very clean hard to find machine that easily powers thru 3 mil and strips.  15″  EdgeController Screen. 1802 […]

Read More →

2008 BIESSE COMIL PERFORMER TP FEED THRU CASE CLAMP $38,000

2008 BIESSE COMIL PERFORMER TP AUTOMATIC FEED THRU CASE CLAMP $38,000 Clean, well maintained, hard to find, Comil TP feed thru case clamp with a 12″-49″ working height, 9.8″-116″ working length, and a 7.1″-39″ working width (min/max). Max beam and conveyor speeds of up to 53 FPM. The clamp conveyor is 200″ long while the […]

Read More →

BLACK BROS 5’X10′ SIDE LOADING COLD PRESS

BLACK BROS 5’X10′ SIDE LOADING COLD PRESS

Read More →

HOUFEK 36″ BULDOG WIDEBELT SANDER $10,000

2007 HOUFEK 36″ BULDOG 910C WIDEBELT SANDER $10,000 The Houfek Buldog 910C is built like a tank. Much heavier in quality than a majority of sanders on the market. This one sports a thick defect free rubber grooved helical head drum, NEW graphite on platen, and a conveyor, that while not perfect, has a lot […]

Read More →

RITTER R-30 TRIPLE SPINDLE DOOR SHAPER $7,500

RITTER R-30 TRIPLE SPINDLE DOOR SHAPER $7,500 This is a Ritter R-30 which has 3 shaper spindles mounted in a common base with a 38″ x 64″ worktable. Designed for running raised panels, style & rail material, and tenons for raised panel doors. Equipped with 1-1/4″ diameter spindles. Spindles are powered by (1) 7.5 HP […]

Read More →

WEGOMA SD16S DOUBLE HEAD 16″ COMPOUND MITER SAW $8,000

WEGOMA SD16S DOUBLE HEAD 16″ COMPOUND MITER SAW $8,000 This is a great option for those looking to cut wood, plastic, or even aluminum (oil mist system included).  FEW SAWS can offer all that a Wegoma has to offer. Twin 2.2 KW/3 hp motors allow for ample power for the 16″ blades that allow a […]

Read More →

BRANDT KTD 72 CONTOUR EDGEBANDER $6,000

BRANDT KTD 72 CONTOUR EDGEBANDER $6,000 Clean, and complete KTD 72. Clean as in the glue pot and all associated parts are 100% clean PLUS the glue pot was recently rebuilt. Add to the the fact that you also get pre-heat and even the original fence and manual! Very clean well maintained machine. This fully functional […]

Read More →

LIGMATECH MPH 40 CASE CLAMP

LIGMATECH MPH 40 CASE CLAMP $$$RECENTLY SOLD$$$ Fully functional, well maintained, cleaned and checked Ligmatech MPH 40 Case Clamp. It will close to a minimum of  13.5″ tall X 10.5″ wide to a maximum of opening of 55.5″ tall X 103″ wide. Maximum clamping depth is 37″. The Ligmatech Electric Case Clamp, Model MPH-40, is […]

Read More →

STENNER VHM 36″ RESAW 25HP $14,000

STENNER VHM 36″ RESAW 25HP $14,000 Beautiful example of the famous VHM by Stenner! Clean, original paint (yes, the covers are that glossy and original to the machine), single owner Stenner VHM. This one comes from a railroad yard and was used sparingly to resaw lumber for floors during car rebuilds, retrofits, and repairs. Thus […]

Read More →

WHITNEY S-970 HELICAL TOP & BOTTOM 36″ PLANER $24,000

WHITNEY S-970 HELICAL TOP & BOTTOM 36″ PLANER $24,000 Clean S-970 planer with Helical Oliver Straitoplane heads. 40 HP on the top head and 30 HP on the lower head. 36″ X 7″ capacity. Complete with dual grinding bars and sharpener. Variable feed speed (10 hp) via a VFD. Cabinet mounted controls. Grinder, top grinding […]

Read More →

WEINIG UNIMAT 500 MOULDER $$$SOLD$$$

WEINIG UNIMAT 500 MOULDER $$$RECENTLY SOLD$$$ This is not the cheapest 500 nor the most expensive one out there. It is however the cleanest and lowest hour Unimat 500 you will find. Used very sparingly for short run work! All you have to do is pop the hood and you can see that this is […]

Read More →

GRIGGIO SC3200E SLIDING TABLE SAW W/TIGERSTOP FENCE $8,000

GRIGGIO SC3200E SLIDING TABLE SAW W/TIGERSTOP FENCE $8,000 Clean 10′ Griggio slider with a 9 Hp main motor and 18″ (450 mm max.) blade capacity that also features 3 arbor speeds (3200/4000/6000) with the flip of a belt. Still want more? How about a scoring blade powered by it’s own 3/4 hp motor? Still want […]

Read More →

LARICK 410S SHAPE AND SAND

LARICK 410S SHAPE AND SAND Shaper Motor:  7.5 HP Belt Driven Shaper Spindle Speed:  4000-7000 rpm Shaper Spindle:  1-¼” Dia. Sander Motors:  1.5 HP Direct Drive Sander Spindle Speed:  400-1800 rpm  Sander Spindles:  1″ Dia. by 4″ Tall  Voltage:  208-240V 3ph, 30A Conveyor:  6″ Wide, 4 rows of tires  Vertical Adjustment:  Yes, with digital counters  Horizontal Adjustment:  Yes, […]

Read More →

2014 TIMESAVERS PUMA 3 HEAD WET 52″ WIDE BELT SANDER

2014 TIMESAVERS PUMA 3 HEAD WET 52″ WIDE BELT SANDER GRINDER DEBURRING/FINISHING METAL/SOLID SURFACE $$$RECENTLY SOLD$$$ This is truly a rare find. You simply don’t find machines (especially wet) for nearly 70% off the NEW cost with such low hours. This is a 3 head 52″ wide machine with an air knife for drying your […]

Read More →

2007 WEIMA WL 10/45 V-ROTOR GRINDER 51KW/68HP

2007 WEIMA WL 10/45 V-ROTOR GRINDER 51KW/68HP $$$RECENTLY SOLD$$$ This particular WL 10/45 was made on 09/2007 and has 5,934 hours on it. V-Rotor head has all NEW knives installed.  It also features the largest motor available on the WL10 and the head has the largest knife option with 52 total knives.  The “WL” shredder […]

Read More →

MIKRON M645 MULTI MOULDER $6,500

MIKRON M645 MULTI MOULDER ARCH SHAPER $6,500 Designed for curved casings, crowns, circles, ellipses and straight mouldings. Equipped with: (1) 1-1/4″ arbor, 6″ max. width x 7″ max. thickness capacity. 5 HP Baldor spindle motor with cutter-head speed of 6,000 RPM. Spindle with forward & reverse rotation; cutting dimensions 6-1/2″ max. cutting circle horizontal, 6″ […]

Read More →

2016 MARTIN T12 SHAPER & 4 ROLL POWERFEED W/34 HOURS

2016 MARTIN T12 SHAPER & 4 ROLL POWERFEED W/34 HOURS $$$RECENTLY SOLD$$$ Martin model T12 Shaper with under 34 total hours (absolute hour meter/not re-settable/hour meter runs when head is on only). This T12 Shaper is powered by a 5.5 kW (7.5 HP) motor with a 1-axis control and 5.7″ cutting height. Rotational speeds including […]

Read More →

2016 MARTIN T45 PLANER W/80 HOURS

2016 MARTIN T45 PLANER W/80 HOURS $$$RECENTLY SOLD$$$ Martin model T45 thickness planer with 80 hours (absolute hour meter/not re-settable/hour meter runs when head is on only). 24″ width capacity. Digital readout w/ single axis controller for table positioning, 10hp, 220v, 3ph main motor w/ safety brake, infinite feed speeds, Tersa cutterhead, rubber infeed/outfeed rollers, […]

Read More →

AUTOQUIP 2,500 LB LIFT TABLE 48″ X 48″ $1,400

AUTOQUIP 2,500 LB LIFT TABLE 48″ X 48″ $1,400 This fully functional machine has been fully cleaned, checked, and is ready to work from the time you receive it. No hydraulic leaks, bad hoses, or leaky seals. 48″ X 48″ table capable of lifting 2,500 lbs to 42″.  6-1/2″ lowered height. It is powered by […]

Read More →

TAYLOR 8 SECTION LARGE CAPACITY ROTARY DOOR CLAMP $10,000

TAYLOR 8 SECTION LARGE CAPACITY ROTARY DOOR CLAMP $10,000 This is a very hard to find 8 section rotary clamp. It has a generous 42″ X 86″ of clamping space per section. It was also ordered with 3 horizontal clamps and 4 vertical clamps for a total of 7 clamps per section. (56 total clamps) […]

Read More →

OSAMA S2R 1300 TOP & BOTTOM GLUE SPREADER $4,800

OSAMA S2R 1300 TOP & BOTTOM GLUE SPREADER $4,800 This top and bottom glue spreader features a 1300 mm working width or 48-3/16″ (52-3/8″ actual roll width). with a 4″ daylight opening. 5 hp motor runs at 18 m/min Machine is currently wired 230V/3 Phase. Machine is in overall good condition. This fully functional machine has […]

Read More →

DIEHL NO 75 STRAIGHT LINE RIP SAW $6,750

DIEHL NO 75 STRAIGHT LINE RIP SAW $6,750 This workhorse is powered by a 15 hp (3,450 RPM) main motor with a 3 hp motor on the feed. It is capable of 30-50-75 & 120 FPM. 2″ dia. arbor with an 18″ blade cap.  4″ max. depth of cut, 12″ min. part length, 21-1/2″ width of table […]

Read More →

NEW JOOS HOT PRESS

NEW JOOS HOT PRESS  Contact us for a quote today! We have seen a lot of presses. If we had a choice we would buy Joos and Joos alone. We choose Joos because of the stellar service and support Joos USA offers in addition to the the quality of every component on a Joos press. From […]

Read More →

2007 TIMESAVERS 3 HEAD 2300 SERIES 43″ WIDEBELT SANDER W/4,358 HOURS

2007 TIMESAVERS 3 HEAD 2300 SERIES 43″ WIDE BELT SANDER W/4,358 HOURS $$$RECENTLY SOLD$$$ Clean Timesavers 2300 series 3 head widebelt sander with 4,358 hours. First head is a 25 hp helical grooved 8″ rubber drum. Second head is a 20 hp helical grooved 8″ rubber drum. Third head is a combination head with a 15 […]

Read More →

MAY COATING TECHNOLOGIES 450 lb/hr HOT MELT DISPENSER DRUM UNLOADER $12,000

MAY COATING TECHNOLOGIES 450 lb/hr HOT MELT DISPENSER DRUM UNLOADER $12,000 We pulled this Acumeter Technologies/May Coating Technologies model  400 DG MCE off a Black Bros line that we recently sold. This is a fully operational hot melt dispenser drum unloader built in 2006. Very hard to find on the used market.  It is capable […]

Read More →

2012 WEINIG POWERMAT 600 CNC/POWERLOCK/800 HOURS

2012 WEINIG POWERMAT 600 CNC/POWERLOCK/800 HOURS $$$RECENTLY SOLD$$$ This Powermat 600 was put into service on 12/03/2013 and has just a hair under 800 run hours spending most of that time primarily running pine. Includes one set of Powerlock heads and manuals per picture. Head #1 Bottom Head (planing) 11 KW/15 HP Head #2 Right Head 7.5 […]

Read More →

BLACK BROTHERS END LOADING 5 X 10 AIR POD COLD PRESS W/ADJUSTABLE OPENING

BLACK BROTHERS END LOADING 5 X 10 AIR POD COLD PRESS W/ADJUSTABLE OPENING $$$RECENTLY SOLD$$$ This is a 15 PSI end loading pod press. 62″ X 122″ platens with a motorized adjustable daylight from 2″ to 49″.  3 rows of 5 pods for a total of 15 air pods. Very clean machine. Air hose actuated roller […]

Read More →

TAYLOR 40 SECTION CLAMP CARRIER $7,000

TAYLOR 40 SECTION CLAMP CARRIER $7,000 This is a pretty straight forward machine. 40 section 8′ wide clamp carrier. 182 clamps with a 32″ capacity. (plus 8 parts clamps). The machine also has 38 thin material hold down bars.  Pneumatic board flatener. Pneumatic clamp tightening. Pneumatic rotation.

Read More →

2014 HAFELE FUTURA 250 HINGE BORING, RTA, DRILLING & INSERTION MACHINE $2,000

2014 HAFELE FUTURA 250 HINGE BORING, RTA, DRILLING & INSERTION MACHINE $2,000 This machine is set up to drill and insert RTA fittings currently. Very hard to find used plus it’s a 2014 model year. Powered by a 1-1/2 hp 230V/3 Phase motor. Pneumatic drilling unit with push button controls. (also has optional foot pedal) 10’6″ […]

Read More →

2010 SCMI S 630 E CLASS 24″ PLANER W/BYRD SHELIX HELICAL HEAD $SOLD$

2010 SCMI S 630 E CLASS 24″ PLANER W/BYRD SHELIX HELICAL HEAD $SOLD$ Yes, you read that correctly a S630 with a 9 row BYRD SHELIX helical head with 249 15 mm inserts. Also remember this is the more heavily built E Class. This very low use machine is in Excellent condition! Don’t let this […]

Read More →

DIEHL SL-52 WIDE ARM GLUE LINE STRAIGHT LINE RIP SAW

DIEHL SL-52 WIDE ARM GLUE LINE STRAIGHT LINE RIP SAW $RECENTLY SOLD$ The chain on this SL-52 WA has 90%+ chain life or better left in it. Just look at the pictures! This is a glue line capable machine. The arbor runs smooth and true. It is powered by a 15 HP motor while the […]

Read More →

LOBO DOUBLE SIDED OSCILLATING EDGESANDER $3,400

LOBO DOUBLE SIDED OSCILLATING EDGESANDER $3,400 Smooth running double sided oscillating edgesander (Lobo model EGS-947) Max. sanding area 9″ X 48″. Main motor is 5 hp and the machines is currently wired 230V/3 Phase. NEW graphite on both platens. This fully functional machine has been fully cleaned, checked, and is ready to work from the […]

Read More →

BALESTRINI MINI C 2500 DOUBLE SIDED TEMPLATE PROFILE SHAPER $8,000

BALESTRINI MINI C 2500 DOUBLE SIDED TEMPLATE PROFILE SHAPER $8,000 Very clean Mini C 2500. We replaced several air solenoids and installed several piston rebuild kits. This one comes equipped with a pair of Oertli 4″ X 6″ spiral insert cutter-heads. Max length 2500 mm (98.4″). Max height 180 mm (7″). Spindle speed 8400 RPM. Feed speeds […]

Read More →

RFS 20KW RADIO FREQUENCY GLUER $12,500

RFS 20KW RADIO FREQUENCY GLUER $12,500 Single owner shuttle style machine. 20 KW radio frequency generator with an 80″ X 36″ X 4″ capacity. Material is clamped from 3 sides via 4 top, 3 edge, and 9 side hydraulic pushers.  Built in timer and adjustable RF. A very nice clean and complete machine with a large […]

Read More →

FLETCHER FM-2001 TOP AND BOTTOM TRIMMER $4,000

FLETCHER FM-2001 TOP AND BOTTOM TRIMMER $4,000 These are made by Fletcher and were also sold under the Delmac brand for well over a decade. Very well built and this machine can handle 3 mm material! Over head control panel for easy operator access, Non-marring phenolic top, heavy fabricated steel base, polished chrome copy shoes […]

Read More →

CTD D22 DOUBLE MITER SAW W/IN/OUTFEED TABLES $3,400

CTD D22 DOUBLE MITER SAW W/IN/OUTFEED TABLES $3,400 This fully functional machine has been fully cleaned and checked and is ready to work from the time you receive it. It features a 12″ blade Capacity and a fixed cutting angle of 22.5 degree. Motors are 1.5 hp Baldors and are 115/230V single phase. Dual pneumatic […]

Read More →

PINHEIRO PMC 4-450 18″ 4 SIDED PLANER SOLD

PINHEIRO PMC 4-450 18″ 4 SIDED PLANER $$$SOLD$$$ Very very clean and well maintained PMC 4-450! This is the original condition……original paint……….this Pinheiro has a lot to offer and is in top condition. The beds show a minimal amount of wear for a machine this age. Top 4 knife cutter-head is powered by an 18 […]

Read More →

DELMAC DMG 62CT or FRAVOL AZ/2 TOP & BOTTOM TRIMMER $3,000

DELMAC DMG 62CT or FRAVOL AZ/2 TOP & BOTTOM TRIMMER $3,000 This is a low use Italian made Fravol AZ/2 top and bottom trimmer distributed by Delmac in North America as a DMG 62CT. Mechanically it is in excellent plus condition. It’s only downfall is that it has scratches on the case as the previous […]

Read More →

WEGOMA MPA-2 CORNER CLEANER $2,500

WEGOMA MPA-2 CORNER CLEANER $2,500 (reduced) Dual head corner cleaner in good operating condition. We replaced and/or rebuilt 5 air cylinders in total to guarantee it is in good operating condition. Currently wired 230V/3 Phase. 2 sets of tooling included. In above average condition considering other MPA-2’s out there.

Read More →

ARCHER 100 HP BLOWER $3,600

ARCHER 100 HP BLOWER $3,600 This blower runs off a newer (2006) Toshiba 100 HP motor. The inlet measures 33″ and the outlet measures 26″ X 29″. The fan has a diameter of 56″ and the housing approximately 76″.

Read More →

1995 NORTHFIELD 24″ JOINTER SOLD

1995 NORTHFIELD 24″ JOINTER $$$SOLD AS IT LISTED$$$ This machine was used sparingly in a pattern shop and is a single owner machine. What also makes it a great find is that it is a 1995 model. It is wearing it’s original paint and has no repairs. It also features a 10 hp 230/460V Reuland […]

Read More →