SCMI T130 SHAPER W/POWERFEED $3,500

SCMI T130 SHAPER W/POWERFEED $3,500

Yes, this T130 has below average looks, scratches on the top, and the 1-1/4″ spindle is missing it’s nut. On the other hand it is powered by a 9 HP motor featuring forward and reverse. Both the spindle lock and foot brake function as they should. The spindle raises and lowers effortlessly. All 8 Speeds on the Seco 1 HP Powerfeed work as they should. The powerfeed also sports new wheels with interchangeable hubs. This machine is wired 230V/3 Phase.

***This particular machine is a clearance machine and clearance priced to make room for new inventory.

****This machine is non-returnable and does not have a warranty. While it is smooth and strong running it is not perfect and is priced accordingly.

 

WYSONG NO 315 6″ SINGLE SIDED EDGESANDER $750

WYSONG NO 315 6″ SINGLE SIDED EDGESANDER $750

It ain’t pretty, but it is a yellow label Wysong that runs both quietly and smoothly. The 6-1/2″ tall X 32″ long platens were in decent shape. They did have a line worn into the plates lengthwise from the top edge of the paper rubbing them. We did install new graphite. Both tables tilt. The 2 HP motor is wired 480V/3 Phase and only wound 480V/3 phase.

***This particular machine is a clearance machine and clearance priced to make room for new inventory.

****This machine is non-returnable and does not have a warranty. While it is smooth and strong running it is not perfect and is priced accordingly.

SCMI M3 GANG RIP SAW $2,750

SCMI M3 GANG RIP SAW $2,750

Pre-Owned SCM M3 Gang Rip Saw. 60 HP main motor. 2 HP feed motor. Automatic chain lubrication with four rows of anti kick-back fingers. Saw cartridge sleeve with spacers. Long infeed fence. Shaving hood. Mono block base with cast feed table and feed chain. Maximum depth of cut 4-3/4″. Maximum working width 11-7/8″. Feed track width 11-7/8″. Feed speeds of 30-150 FPM.  Throat depth 8-3/4″. Minimum board length 12″. Saw blade diameter 11.8″ to 14″.

***This particular machine is a clearance machine and clearance priced to make room for new inventory. Note: Dust hood needs to be welded/repaired. See pictures of chain for condition.

SULLAIR 10 HP ROTARY SCREW COMPRESSOR $850

SULLAIR 10 HP ROTARY SCREW COMPRESSOR $850

This is a Sullair model 6E-10.0H rotary screw compressor. It is rated at 38 CFM @ 125 PSI and has an 80 gallon air tank. Hour meter is original to the machine and reads 6,423 hours.  Manual and Automatic modes. We have cycled this compressor half a dozen times with out issue.

***This particular machine is a clearance machine and clearance priced to make room for new inventory.

****This machine is non-returnable and does not have a warranty. While it is smooth and strong running it is not perfect and is priced accordingly.

BAURLE SFM DOUBLE SPINDLE SHAPER $1,750

BAURLE SFM DOUBLE SPINDLE SHAPER $1,750

This is a bit of a rare machine in both existence and how cutting edge it was for it’s time. This one sports 1-1/4″ spindles with 5-1/2″ under the nut. It is powered by twin 3/4 KW multi speed spindle motors. Meaning either 3 KW or 4 KW depending on speed. Making it either 4 or 5 hp. Speeds of 2800-4500-5600-6000-9000-12,000 RPM can be achieved via a combination of belt swapping and choosing the proper motor speed of high or low. This machine does feature clockwise and counter clockwise rotation as well as spindle locks. The brakes are incomplete and do not function. Table Size is 79” x 36”. This particular machine is clearance priced to make room for new inventory.

****This machine is non-returnable and does not have a warranty. While it is strong running it is not perfect and is priced accordingly.

EKSTROM CARLSON DOUBLE SPINDLE SHAPER $1,750

EKSTROM CARLSON DOUBLE SPINDLE SHAPER $1,750

This double spindle shaper sports twin 6″ long X 1-1/4″ spindles. It is powered by a pair of 5 hp motors that both have working short stop brakes. The table top measures 38″ X 62″. This particular machine is clearance priced to make room for new inventory.

****This machine is non-returnable and does not have a warranty. While it is strong running it is not perfect and is priced accordingly.

CUSTOM 84″-102″ DOUBLE END CUT OFF SAW $2,000

CUSTOM 84″-102″ DOUBLE END CUT OFF SAW $2,000

If you have the need to trim both sides of your product this might fit your needs. It was originally built to square up doors. Down the center of the machine you will find a single belt driven shaft powered by a Marathon 7.5 hp motor. To the right of the machine you will find a fixed saw blade. To the left you will find a movable saw blade riding on a 23″ long 2″ arbor. The blade locks in place via 2 collars and a spacer allowing for approximately 18.5″ of travel. This will allow for an adjustable width from 84-102″.  Max blade diameter is 20″. The chain features sets of ears every 70″. The saw is very easy to use. You simply power on the saw and hit the foot pedal to cycle the machine. Every time the foot pedal is hit the chain will advance 70″ then stop allowing your operator to load the machine. This particular machine is clearance priced to make room for new inventory.

****This machine is non-returnable and does not have a warranty. While it is strong running it is not perfect and is priced accordingly.

CEMCO 5 HEAD VERTICAL BORING MACHINE $5,000

CEMCO 5 HEAD VERTICAL BORING MACHINE $5,000

This Cemco vertical boring machine currently has 5 heads. The current controls support up to 7 heads with a possibility of 8 more additional more heads as well. Motors are all currently 2 HP, 1,725 RPM Baldors including the hydraulic motor. The table is 10′ 3″ long. Double hand safety controls are also included. While this is a fully functional machine that has been fully cleaned and checked, this particular machine is clearance priced to make room for new inventory.

****This machine is non-returnable and does not have a warranty. While it is strong running it is not perfect and is priced accordingly.