SCMI SANDYA 5 SINGLE HEAD 43″ WIDEBELT SANDER $7,800

SCMI SANDYA 5 SINGLE HEAD 43″ WIDEBELT SANDER $7,800

Clean, smooth running, and electronic eye tracking Sandya 5. 43″ working width with a 7″ maximum thickness capacity.  This sander features a combination head with a 5-1/2″ helical grooved, freshly dressed defect free rubber drum. This head is powered by a 13 KW/17.5 HP motor. The platen has NEW felt and graphite. The feedmat is clean, and defect free showing about 40-50% life remaining. It is powered by a .9 KW/ 1.2 HP multiple speed gear box capable of  4-20 m/min (13-65 FPM). Machine also features a digital read out, motorized rise and fall of the table (manual as well), along with auto calibration. NEW brake pad installed. Machine is currently wired 230V/3 Phase and is rated @ 50 amps at 230V. This fully functional machine has been fully cleaned, checked, and is ready to work from the time you receive it.

EXTREMA 36″ PLANER SANDER

EXTREMA 36″ PLANER SANDER

This Extrema Planer/Sanders is equipped with a single combination head plus a STEALTH helical Cutter Head, pneumatic cylinder”for removing dust shroud from planer head”, Square D electric controls and Camozzi Pnematic disc brakes on sanding and planing head.  Air jet belt cleaning device, panel cleaning brush at outfeed, vacuum bed as well as front and rear bed extension.

  • Ability to plane and sand in one single pass
  • Heavy duty steel mono-block construction
  • STEALTH Helical cutter head for high quality, low tare-out planing
  • Four post screw jack elevation system for maximum stability
  • High quality Goodyear conveyor belts
  • Digital PLC thickness controller
  • Electronic eye tracking system using reliable Omron components
  • Double hold down rollers with hold down shoes at infeed and outfeed.
  • Over thickness safety device and emergency stops at front and rear.
  • Combination sanding head with extra wide 2-1/2″ adjustable platen.
  • Pneumatic disc brakes on sanding and planing head
  • High quality Square D electrical controls
  • Infinitely variable speed drive unit 15-50 ft/min
XSP-1B37
Width 37″
Planer Motor 25 HP
Sander Motor 20 HP
Cutterhead RPM 6000
Cutter Rows 6
Head Type Stealth
Sanding Head Count 1
Contact Drum Size 5″
Max Thickness 6″
Min Thickness 1/8″
feed Speed 15-50 ft/min
belt Size 37 x 75
Feed Motor 2 HP
Elevation Motor 0.5 HP
CFM Requirements 3200
Amps (220V / 460V) 116 / 58
Weight 5100 lbs

TIMESAVERS  SPEEDSANDER 37″ WIDEBELT SANDER $6,800

TIMESAVERS  SPEEDSANDER 37″ WIDEBELT SANDER $6,800

This sander has a newly dressed blemish free drum and NEW graphite on the platen. Excellent mechanical condition.  This fully functional machine has been fully cleaned, checked, and is ready to work from the time you receive it. See detailed specs below:

  • Number of Heads: 1
  • Head Types: Combination
  • Machine Width:  37”
  •  10 HP Main Drive Motor (230v/3 phase)
  • 60” Abrasive Belt Length
  • 0-4” Bed Opening (34”-38” Passline)
  • 10-30 FPM Feed Speed
  • 4” Rubber Covered Drum
  • 1.5” Wide Platen
  • 2 Bed Jacks

LOBO DOUBLE SIDED OSCILLATING EDGESANDER $3,400

LOBO DOUBLE SIDED OSCILLATING EDGESANDER $3,400

Smooth running double sided oscillating edgesander (Lobo model EGS-947) Max. sanding area 9″ X 48″. Main motor is 5 hp and the machines is currently wired 230V/3 Phase. NEW graphite on both platens. This fully functional machine has been fully cleaned, checked, and is ready to work from the time you receive it.

  • Sand paper automatically oscillates up & down, so it will not overheat to get longer life usage and better finish result.
  • 8″ x 20″ end table mounted at left side of the machine to use as contour sanding.
  • Heavy gauge sheet metal cabinets stand and table for heavy work.
  • The height of front & back table is adjustable for 5″.
  • Easily adjustable belt tension device.
  • Two 47″ W x 11-3/4″ D working tables can be tilted up to 45 degrees, reducing material burning and promotes longer belt life.
  • The graphite pad lubricates the sanding belt and allows the belt to run cooler and smoother.
  • All sealed long-life ball bearings and rubber contact motor pulley.
  • Several typical profile blocks can be used for the edge profile sander.
  • Powerful industrial motor for durability usage.
  • Overload protect magnetic switch.

NORTHTECH 3 HEAD 43″ PLANER SANDER

NORTHTECH 3 HEAD 43″ PLANER SANDER

First Head helical insert (planing), second head helical drum/sanding, third head combination (sanding)

OAKLEY H5 DUAL SIDED OSCILLATING EDGE SANDER $4,250

OAKLEY H5 DUAL SIDED OSCILLATING EDGE SANDER  $4,250

This is a very solid, nice looking, well maintained Oakley H5. It is both double sided and also oscillates. Side tables measure 11-1/2″ X 62″ while the platens measure 9″ X 52″. End table measures 20″ X 27-1/2″. All tables raise, lower, and tilt. Main motor is 7.5 hp while the oscillating motor is 1/2 hp. Machine is currently wired 220V/3 Phase. NEW graphite on platens and NEW bearings in front drum. Rear and front drum rubber in good condition.  This fully functional machine has been fully cleaned, checked, and is ready to work from the time you receive it.

TIMESAVERS 2300 SERIES 43″ DUAL HEAD WIDEBELT SANDER SOLD

TIMESAVERS 2300 SERIES 43″ DUAL HEAD WIDEBELT SANDER $$$SOLD$$$

Clean Timesavers 2300 series dual head widebelt sander with 2,551 hours. First head is a 25 hp helical grooved 8″ head with NEWLY recovered drum (NEW bearings on this head as well). Second head is a combination head with a defect free/dressed 20 hp helical grooved 5″ head. Platen has a 2-1/2″ wide face and has NEW graphite and NEW felt. Dial indicators on all drums and platens. The feed is VFD controlled from 20-45 FPM and features a centralized control panel with digital thickness readout (w/NEW battery for memory). Also includes an Auto set up device for thickness. The feedmat has been replaced with a  NEW 3 ply rough top brown nitrile mat. Double infeed and outfeed holddown rolls. Main motor load meters/Watt meters. Four bed jack screws.  43″ X 75″ abrasive belt size. Disc brakes on main motors. Motorized lift with 0-5″ opening (33-38″ passline). 14″ infeed loading area. 15″ minimum part length. Machine is rated at 118 amps @ 230V/3 phase. Full set of original manuals.

2016 TRUPRO PFS-512N DOUBLE SIDED OSCILLATING CURVED SANDER $3,500

2016 TRUPRO PFS-512N DOUBLE SIDED OSCILLATING CURVED SANDER $3,500

We purchased an entire shop and this one came out of it. Very low use and in excellent condition. Max height is 12″ with a max width between spindles of 4.” Machine can oscillate from 8″-12″ (meaning four total inches of oscillation/oscillation may limit height) or it can be used at 12″ if that is the height you require. Main sanding spindles have variable speed from 0-1,800 RPM. Feed features both forward and reverse along with variable speed from 0-1,800 RPM. If you wonder who TruPro is then please go to http://www.trupro-machine.com/ REALIZE that they manufacture a lot……and we mean a lot of machines you see on the market that are re-labeled/re-branded. Also included are over 75 abrasive belts.

FEATURES:

  • Infinitely variable speed of sanding belt and feeding, suitable for different stock material and even sealer sanding.
  • 12”L (PFS-512N) belt drum.
  • Patent design for long term mass production.
  • Sanding stocks of chair back. Arm….etc.
  • Switch for sanding forward or reversely to get the best effect in workpiece.

SPECS:

Sanding belt drive motor 1.4 HP×2 Sanding belt speed 0~980 M/min Sanding belt size 305×850 mm Sanding drum size Ø 175×305 mm Sanding belt oscillation motor 1/4 HP (X2) Sanding belt oscillation range 100 mm Feeding motor 1/4 HP×4 Feeding speed 0~28 M/min Feeding roller size Ø 100×50 mm Feeding roller number 12 pcs Working thickness 6~100 mm Working height 25~300 mm Working length 400~1500 mm Machine size 1050×1100×1150 mm Packing size 1150×1200×1350 mm /600 kgs

OPTI-SAND DUAL HEAD 52″ PANEL SANDER $16,000

OPTI-SAND DUAL HEAD 52″ PANEL SANDER $16,000

This Opti-Sand dual head Panel Sander is designed to finish sand and sealer sand flat panels and other 2 dimensional wood parts in a single pass and cabinet doors, entry doors and other 3 dimensional parts with multiple passes. This is a really well maintained low hour machine. Both heads can run up to 600 RPM and are also reversible. The feed is adjustable up to 44 FPM. Machine is wired 230V/3 Phase and rated at 40 amps. Each head is powered by a 5 hp motor while the feed is powered by a 1.5 hp motor. Easy to use touch screen control. Nice compact size taking up only 6′ X 6′ space while having a nice wide 52″ capacity and a thickness capacity of 4″ (max. thickness capacity shown in pictures). Over all condition is Excellent. This fully functional machine has been fully cleaned, checked, and is ready to work from the time you receive it.

TIMESAVERS 36″ PLANER SANDER W/HELICAL HEAD/ 1,636 HOURS SOLD

TIMESAVERS 36″ PLANER SANDER W/HELICAL HEAD/ 1,636 HOURS $$$RECENTLY SOLD$$$

This machine came in on trade and only has 1,636 hours on it. The first head is a 30 hp helical planer head with 9 rows and 300 inserts. We cleaned and serviced the head and replaced all 300 carbide inserts. They are 4 sided and we are told that you can expect to produce around 150,000 board ft per turn. The second head is a 20 hp combination head featuring a 5″ helical grooved rubber head with platen. We dressed the drum and it is defect and memory free. Grooves are deep and we would estimate it to have at least 80% life left in it. The machines comes with 2 platens, one installed in the machine and a second one as well (different felt densities). We replaced graphite on both and the felt on one. We also upgraded the feed mat to a brown nitrile rough top belt. It offers better grip which equates to a better finish of your product when it exits the machine. This machines also features digital thickness read out and control along with auto thickness calibration. PLEASE NOTE: We are not selling you a machine just pulled from a shop, but a machine ready to be put back to work.  All the critical and expensive consumable parts of this machine have been serviced or replaced as they should be when you purchase a used machine. This fully functional machine has been fully cleaned and checked and is ready to work from the time you receive it.

Series 2300 specifications:

First head 30 hp

Second Head 20 hp

Centralized control panel

Digital thickness readout

Double infeed and outfeed holddown rolls

Hour meter (indicating 1,636 hours)

Main motor load meters/Watt meters

Four bed jacks

Infeed stop bar

Drums and combination head types standard

Dial indicators on drums/platens

5-1/2″ diameter  combination head)

2 1/2″ width platen on combination head

75″ abrasive belt length

Disc brakes on main motor

20-45 FPM feed speed A/C

Auto set-up device

Motorized lift

0-4.5″ opening (33-38″ passline)

14″ infeed loading area

Through-beam abrasive belt tracking

15″ minimum part length

STANDARD FLAP & PNEUMATIC DRUM SANDER $2,750

STANDARD FLAP & PNEUMATIC DRUM SANDER $2,750

You get a lot of flexibility when you buy this well kept machine. It can be either a flap sander, a pneumatic drum sander, or both. As there are enough parts to configure it either way. It is powered by a 230V/3 Phase motor. All belts and bearings are in excellent condition. This sander is made by Standard and the model is a 7RSBY. This fully functional machine has been fully cleaned and checked and is ready to work from the time you receive it.