CUSTOM 84″-102″ DOUBLE END CUT OFF SAW $2,000

CUSTOM 84″-102″ DOUBLE END CUT OFF SAW $2,000

If you have the need to trim both sides of your product this might fit your needs. It was originally built to square up doors. Down the center of the machine you will find a single belt driven shaft powered by a Marathon 7.5 hp motor. To the right of the machine you will find a fixed saw blade. To the left you will find a movable saw blade riding on a 23″ long 2″ arbor. The blade locks in place via 2 collars and a spacer allowing for approximately 18.5″ of travel. This will allow for an adjustable width from 84-102″.  Max blade diameter is 20″. The chain features sets of ears every 70″. The saw is very easy to use. You simply power on the saw and hit the foot pedal to cycle the machine. Every time the foot pedal is hit the chain will advance 70″ then stop allowing your operator to load the machine. This particular machine is clearance priced to make room for new inventory.

****This machine is non-returnable and does not have a warranty. While it is strong running it is not perfect and is priced accordingly.

CTD DM200R 14″ DOUBLE END MITER SAW W/OIL MISTER $4,000

CTD DM200R 14″ DOUBLE END MITER SAW W/OIL MISTER $4,000

This is a nicely equipped double end miter saw with adjustable centers up to 8′. It adjusts via a hand wheel and features an optional Accurate Technologies Digital read out for ease of set up. Power is provided via twin upgraded 3 HP saw duty Baldor motors and the machine is also equipped with an optional Accu-Lube Oil Mist system which is hard to find on these machines. Further more you will find that each head has optional vertical and horizontal pneumatic hold downs. As you can tell there are a lot of “options” added onto this machine. You will also find pedestal dual palm safety controls. This fully functional machine has been fully cleaned, checked, and is ready to work from the time you receive it. This is our guarantee to both you and your company!

Specifications:

  • Double end trim mitre saw

  • Blade Capacity: 14″

  • Magnetic Starter

  • 10 strokes per min.

  • Mitres up to 45°

  • Cutting Capacity:

  • 45°: 1½” X 5″

  • 90°: 2″ X 7¾

  • Uses our time tested 200R Series Saw Head; precision ball bearing spindle and pivot shaft are sealed and preloaded for guaranteed accuracy; .001 alignment of spindle and pivot shaft.

  • 1″ 25mm with 2-1/2″ 64mm saw collars; 3700 RPM of spindle.

  • 3 H.P. 3 Phase 230/460 Volt Totally Enclosed Fan Cooled Motors, 60 Hz, 3450 RPM, with starters and voltage protection

  • Tables are precision machined and ground iron castings with milled keyways in tables to guide fences.

  • Four, 2″ round 51mm outlets are provided, two on each saw head for DM200R; 800 CFM required per saw head.

  • 10 strokes per minute; actual production rates will vary with type and width of material to be cut.

  • Saw heads swivel from 90° to 45° towards each other with degree markings and pointer; stops are at 90° and 45°; angular adjustment of saw head away from each other available as option; other angles possible; phenolic chip breaker included.

  • Heavy gage steel; eight foot centers with traveling right hand carriage on rack and pinion; length measuring scale; optional length centers available to 40 feet 12M; Digital Length Measurement available as optional accessory.

  • Completely encloses blade in rest position. Lower rotating blade guard pivots up into main stationary blade guard as saw heads pivot down to cut.

  • On each side of blade are keyed to base and are easily adjustable front to back, and side to side.

  • Two inside vertical clamps must be tripped by foot valve, then a two-hand anti-tie down, maintained contact safety control will work the air down feed of saw heads. An air filter/regulator/lubricator with auto drain is provided.

  • 75 PSI 5.2kg/cm2; 3 CFM at 75 PSI .09 cubic meters at 5.2 kg/cm2, based on 10 strokes per minute.

  • 32″ 81cm front to back x 64″ 163cm High x 120″ 305cm Long; Weight 1,050 lbs. 476kg.

MARTIN T72 12′ SLIDING TABLE SAW $7,500

MARTIN T72 12′ SLIDING TABLE SAW $7,500

This is a large stroke saw with a large carriage. The slide itself measures nearly 146″. The front of the slide will clear the scoring blade by almost 3 inches and the rear of the slide will clear 3/4 of the main blade when set up in the way you see it. You also have a massive carriage coming in at 52″ deep X 66″ wide not including the sliding table. The cross-cut fence is also massive and features an extension and 2 extra large stops. In case you haven’t noticed this machine is super sized! The rip-cut fence will allow 50″ of clearance to the right of the blade.  Saw blade speeds of 2800, 4,000, and 5,500 RPM can be achieved by moving the belts and yes the “read out mechanism” for the speed via lights does function. Minimum saw blade diameter is 200 mm while the maximum is 450 mm (8-18″). The main blade is powered by a 5.5 KW/7.5 HP motor while scoring is handled by a separate .75 KW/1 HP motor. Both blade angle and raising and lowering of the blade are hydraulic. A NEW hydraulic gas pressure spring assembly has been installed to guarantee this functions properly. Additionally on the rip fence there is a digital read out for blade angle. This fully functional machine has been fully cleaned, checked, and is ready to work from the time you receive it. This is our guarantee to both you and your company!

MEREEN JOHNSON NO 435-H 60″ GANG RIP SAW $18,000

MEREEN JOHNSON NO 435-H 50″ GANG RIP SAW $18,000

This is something you rarely see come to market. If you process a lot of sheets goods into strips look no further because wide gang rips are few and far between. With a 50″ wide x 2-1/2″ maximum thickness capacity (& 60″ long arbor) panels are cut into strips using 12″ maximum diameter tooling. The 50″ wide feed bed consists of aluminum slats with replaceable steel-backed rubber insert strips (Merreen Johnson has quoted us $5,400 for the inserts & hardware if you wish to replace). The feed bed is arranged for friction feeding, with dip at the saw line to allow infinite saw spacing on saw arbor without contacting the feed bed. Precision feed sprockets with hardened teeth. Feed system with oil mist lubrication of bottom chain surface and extended pins on chains including automatic low oil and air supply level control, system shut-off feed drive motor to prevent running machine without proper lubrication. A 4 HP variable speed feed drive with manual adjustment with feed rates from 20 to 75 FPM. The 75 HP saw arbor measures 2-5/8″ in diameter and is 60″ in length. Upper in-feed pivoting anti-kickback assemblies are provided for operator safety. You will get a total of 22 ten inch blades with an arbor size of 3-1/2″ and also included are 10 blade collars. This fully functional machine has been fully cleaned, checked, and is ready to work from the time you receive it. This is our guarantee to both you and your company!

DIEHL SL-52 WIDE ARM GLUE LINE STRAIGHT LINE RIP SAW

DIEHL SL-52 WIDE ARM GLUE LINE STRAIGHT LINE RIP SAW $RECENTLY SOLD$

The chain on this SL-52 WA has 90%+ chain life or better left in it. Just look at the pictures! This is a glue line capable machine. The arbor runs smooth and true. It is powered by a 15 HP motor while the feed is powered by a 2 hp motor. The feed runs as smooth as the arbor and is capable of speeds from 65-195 FPM. 2″ arbor with an 18″ blade capacity can cut material from 1/8″ to 4-1/4″. The table measures 95″ X 79″ and the fence will lock 53″ to the right of the blade with 56 total inches of clearance from the right of the blade to the upright supports. Front adjustable fence locks tight. Automatic chain lubrication system. 1 upper infeed anti-kickback safety guard. 8 spring loaded pressure hold down rollers that are all in very good condition. Adjustable pressure beam with front hand wheel and height controls. Everything raises and lowers throughout it’s range very easily. Front push button controls. Machine weight 6,000 lbs.