2014 RITTER R46VH VERTICAL HORIZONTAL CONSTRUCTION BORING MACHINE

2014 RITTER R46VH VERTICAL HORIZONTAL CONSTRUCTION BORING MACHINE

R46VH Construction Drill– Designed for dowel and hardware connector boring applications for frameless cabinetry. The 46- spindle system allows for 23-spindle horizontal and 23-spindle vertical boring of construction holes for upper and lower cabinetry as well as pantries and drawer boxes. Quick changeover of boring patterns and a one-point panel referencing design eliminates the need to change reference stops and fences for the horizontal and vertical boring applications. The non-tilting boring head design provides for years of boring pattern accuracy.

STANDARD FEATURES:

  • 32mm spindle centers
  • Steel gear driven spindles
  • 23-Spindle horizontal head
  • 23-Spindle vertical head
  • Face edge referencing system
  • Quick tool change system
  • K.D. fitting boring capacity
  • Foot pedal operated
  • Weight: 2,000 lbs.

RITTER R46 DUAL HEAD LINE BORING MACHINE $5,000

RITTER R46 DUAL HEAD LINE BORING MACHINE $5,000

These machines are popular amongst woodworkers. They are built to last and cheap to repair……with the repairs being mostly air leaks. The R46 features dual 23 spindle heads on 32 mm centers with each head being powered by it’s own 3 hp motor. You have a 48″ back fence with dual stops and dual pin sets for indexing longer panels. Plus the heads easily move between 4″-24″ centers on linear bearings and you will even have 4 flip stops for the positioning of the heads as well. This fully functional machine has been fully cleaned, checked, and is ready to work from the time you receive it. This is our guarantee to both you and your company!

  • (2) 3 HP Spindle Drive Motors, TEFC
  • (2) 23-Vertical Gear Driven Spindle Rows
  • 32mm Spindle Centers
  • 10mm Bored Collets
  • (24) Right Hand, (22) Left Hand
  • 4″-24″ Centers Between Rows
  • (4) Quick Set Drill Head Position Stops
  • Heads travel on precision linear bearings
  • Rear Drill Row Nesting
  • 48″ Back Fence with (2) Stops
  • (2) Air Index Pins
  • (2) Position Drill Depth Stop Turret
  • 30″ X 48″ Work Table Surface
  • Wired 3-Phase 240/480 Volt, 60 Hz.
  • Foot Actuated Boring Cycle
  • Crated Dimensions: 54″ X 54″ X 76″ and 1341 Lbs
  • Designed and Manufactured in the USA

SCHULTZFORM SS012 SOLID SURFACE OVEN $3,500

SCHULTZFORM SS012 SOLID SURFACE OVEN $3,500

Clean, hard to find, SchultzForm SS012 solid surface oven with a 30″ X 144″ capacity. See below for more specs. and information. This fully functional machine has been fully cleaned, checked, and is ready to work from the time you receive it. This is our guarantee to both you and your company!

Shape materials faster using infrared and convection technology.

The clam shell design gives you easy access for multiple pieces, It has a clear view window and a precision variable oven temperature controller. The Oven maintains even heat at the temperature you choose and will hold it all day long.  Designed to heat a full sheet of 30″x144″

SchultzForm Solid surface ovens are much faster than conventional ovens because they use a combination of infrared and convection technology to rapidly soak through your solid surface material without over heating it. The ability to form many different shapes with solid surface materials opens up new creative possibilities. SchultzForm solid surface ovens are easy to use and built to last.

Features:

  • Designed to heat a full 30″x 144″ sheet
  • Uses a combination of infrared and convection technology for fast penetration time
  • Clam shell hood opening for easy access
  • Clear viewing window is conveniently located in the front of the oven for checking materials or pointing a laser
  • Non-marking grill
  • Variable oven temperature delivers precise heating rate
  • Legs are removable for easy transportation and storage of the unit when not in use

Applications:

  • Bathroom Vanities
  • Kitchen Counter-tops
  • Table and Bar-tops
  • Window Sills
  • Shower/Tub Enclosures
  • Airport Counter-tops
  • Structural Shapes
  • Hotel/Motel Furniture
  • Restaurant Fixtures
  • Let Your Imagination Run!

Specifications:

    • Surface Width 34″
    • Surface Length 150″
    • Voltage 208-230V/3 Phase @ 30 amps

DODDS C48J DRAWER CLAMP $6,500

DODDS C48J DRAWER CLAMP $6,500

This is a heavy-duty vertical, well maintained, clean, universal drawer box clamp with a fixed left jaw and motorized adjustable right clamping jaw. The operator loads a drawer front & pair of sides into the clamp, then activates the clamping head with dual palm controls. 2″ – 15″ Drawer height, 6″ – 28″ drawer depth, and 4″ – 48″ drawer width cap. Front loading operation assembles drawers with or without lipped fronts. Tunes up and ready to go. New plumbing and many NEW controls installed to make this a reliable clamp for years to come. This fully functional machine has been fully cleaned, checked, and is ready to work from the time you receive it. This is our guarantee to both you and your company!

SCMI ASSEMBLA E CASE CLAMP $22,000

SCMI ASSEMBLA E CASE CLAMP $22,000

This is a really clean, hard to find clamp that was used sparingly! This Assembla E features 1 horizontal and 1 vertical interlocking pressure beam, each with electric push button controls. The beam surface area eliminates the need for pressure pads. 12″ minimum and 100″ maximum length, 31″ max. depth, 10″ minimum and 52″ maximum height. (52-3/8″ X 100-1/8″ max. daylight) Vertical and horizontal interlocking pressure walls move parallel and square the clamp frame. Manual switch setting with LED readout, adjustable pressure regulator clutch system stops the beams at preset pressure resistance. This fully functional machine has been fully cleaned, checked, and is ready to work from the time you receive it. This is our guarantee to both you and your company!

ALTENDORF F45 3200 SLIDING TABLE SAW $9,000

ALTENDORF F45 3200 SLIDING TABLE SAW $9,000

This F45 pre-dates the Elmo, but has tons of features over the average F45. It is also very complete and has multiple accessories that are not often found with the average F45. First off the computer has been bi-passed making this a fully mechanical machine. So rise and tilt of the blade is still achieved via the same motors, but via buttons instead of a keypad. So there are no expensive components to replace and it is better than manually positioning everything. The fence can easily be jogged via the original toggle switch then manually positioned and locked into place. The digital read out for RPM works and the machine features multiple speeds of 3,500, 4,000, 5,000, & 6,000 RPM. Yes, the positioning motors work on the scoring unit. Again only the proprietary computer and keyboard are bi-passed. All motors works as they should. We did install a NEW piston for the tilt and on the scoring tensioner. This machine has a 7.5 hp main motor and a 1 hp scoring motor.  The phenolic ways are in excellent condition. Being a 3200 mm saw you will get approximately 10.5′ out of the slider and the fence will allow for 54″ of travel with the wider fence plate and being that this one has a lot of accessories there is even a slim fence plate that will allow you to gain another 1-3/4″ of travel. As for accessories you will get a lot from a Duplex fence to regular and dado blade guards to wrenches, a material support, flip stops, even a NEW Leuco scoring blade, and more. This fully functional machine has been fully cleaned, checked, and is ready to work from the time you receive it. This is our guarantee to both you and your company!

WHIRLWIND 212R UPCUT SAW W/SCALED OUTFEED TABLE $3,500

WHIRLWIND 212R UPCUT SAW W/SCALED OUTFEED TABLE $3,500

This is a right hand, 10 HP, 18″ blade capacity workhorse. It comes with a scaled outfeed roller table with stops. It has a newer foot pedal, good belts, a NEW Amplifier, NEW pilot valve, and a NEW One Shot Valve Assembly (basically all the pneumatic valves have been replaced). Cutting capacity is 1″ @ 13″, 2″ @ 12″ and 4″ @ 10″ . 1″ arbor and a maximum of (Approximate): 45 – 50 cutting cycles per minute. This fully functional machine has been fully cleaned, checked, and is ready to work from the time you receive it. This is our guarantee to both you and your company!

ONSRUD MODEL 24210-CVS INVERTED PIN ROUTER W/VARIABLE SPEED $3,250

ONSRUD MODEL 24210-CVS INVERTED PIN ROUTER $3,250

This is a bit of a rare machine because it has variable speed from 0-20,000 RPM while the main motor is 10 HP. So you get a whole lot of RPM, a big motor, and control of that power. The throat has 24″ of clearance. The spindle raises and lowers pneumatically and has 0-3″ of spindle travel. This fully functional machine has been fully cleaned, checked, and is ready to work from the time you receive it. This is our guarantee to both you and your company!

MAR-BEL DLS 26 LAMINATE SLITTER 26″ CAPACITY $2,400

MAR-BEL DLS 26 LAMINATE SLITTER 26″ CAPACITY $2,400

 

Designed to provide the owner with maximum throughput for accurate, smooth-edged laminate strips. This machine easily slits vertical or countertop grades without adjustment for the variation in material thickness. The fence has a sturdy double slide-dual mechanism that assures durable, accurate service. Dust free 1/16″ kerf design allows waste to be disposed of through a chute utilizing a free floating extractor blade. Once aligned, the fence offers continuous slitting of material to size. The operator is only required to hold the material against the fence as the blades self feeds the material. This fully functional machine has been fully cleaned, checked, and is ready to work from the time you receive it. This is our guarantee to both you and your company!

Detailed Specifications:
Motor Power .33 HP
Feed Rate 40 FPM
Minimum strip 1/2″
Maximum strip 26″
Electrical 115V/Single Phase

DETEL M-2H DOUBLE ROW 50 SPINDLE LINE BORING MACHINE $4,500

DETEL M-2H DOUBLE ROW 50 SPINDLE LINE BORING MACHINE $4,500

This machine is in very good condition. This 50 spindle line boring machine features 2 spindles with 25 spindles per head on 32 mm centers. Each spindle is driven by a 3 hp motor. Both heads have numeric read outs and can be adjusted from the front and move in and out from 5-25″. Under each head you will find a scaled depth adjustment for the depth of bore. Additionally the dive speed of each head can be independently controlled. Dual overhead hold downs firmly hold down your work piece and can be easily adjusted. A 10′ back fence with built in rulers and 4 flips stops guarantees quick set ups and repeat-ability. You will also find a pair of independently operated pin sets for indexing when boring long panels. The machine cycles via a foot pedal. The only repair we see is to the adjustment handle which has been epoxied. This fully functional machine has been fully cleaned, checked, and is ready to work from the time you receive it. This is our guarantee to both you and your company!

ECCO FLAP & PUMP SANDER $1,200

ECCO FLAP & PUMP SANDER $1,200

This is a Flap & Pump sander in one machine. There is another flap holder in case you want a dual flap machine as well. The flap head is approx. 12″ in diameter while the pump 6″. Machine is currently wired 230V/3 Phase. One dust hood is missing. This fully functional machine has been fully cleaned, checked, and is ready to work from the time you receive it. This is our guarantee to both you and your company!

PRESTO 48″ X 60″ 4,000 LB LIFT TABLE $1,800

PRESTO 48″ X 60″ 4,000 LB LIFT TABLE $1,800

Clean, hard to find size Presto lift table. Model AX40-4860 is a pneumatic lift table capable of lifting 4,000 lbs. It has a lowered height of 8″ and a raised height of 32″.  The top measures 48″ X 60″. This fully functional machine has been fully cleaned, checked, and is ready to work from the time you receive it. This is our guarantee to both you and your company!

NORTHFIELD UNIPOINT 7.5HP RADIAL ARM SAW $2,500

NORTHFIELD UNIPOINT 7.5HP RADIAL ARM SAW $2,500

This Unipoint has a NEW set of motor bearings and runs smoothly. The carriage is tight and slides effortlessly. The 16″ blade is powered by a 7.5 hp main motor that is currently wired 230V/3 Phase and uses a knife switch to turn it on and off.  This particular machine is clearance priced to make room for new inventory. This fully functional machine has been fully cleaned, checked, and is ready to work from the time you receive it. This is our guarantee to both you and your company!

Motor Horsepower  7-1/2 hp
Saw Diameter 16″
Saw Hole 1″
Dado* Largest Width on Standard Mandrel 1-9/16″
Dado* Largest Width on 1-3/8″ Standard Mandrel 3″
Maximum Depth of Cut (16″ Saw) 4-1/2″
Cross Cut Capacity-Guide Fence Regular Position 17-1/2″
Cross Cut Capacity-Guide Fence Rear Position 25″
Ripping Capacity-Between Saw and Regular Guide Fence 23-1/2″
Ripping Capacity-with Guide Fence Moved to Rear 31″
Maximum 45 degree Miter, Guide Fence Regular Position 4″ x 12-1/2″
Moved to Rear 4″ x 14-1/2″
Maximum 70 degree Miter, Guide Fence Regular Position 4″ x 6″
Moved to Rear 4″ x 8-1/2″
Maximum Compound 45 degree Miter 3″ x 12-1/2″
Motor Raises to Center of Arbor to Table Top, Max 10″
Motor Lowers, Center of Arbor to Table Top, Min 3-5/8″
Size of Table 25″ x 48″
Height of Table 32″
Angle Capacity Saw Tilts to Left 45 degrees
Saw Pivot to Right 70 degrees
Saw Pivot to Left 45 degrees
Floor Space, Overall 48″ x 60″
Roller Tables, Length from Saw Blade to Each End 10′
Roller Tables, Width Overall 17-1/2″
Approx. Net Weight 800 lbs
Approx. Shipping Weight 1000 lbs
Approx. Shipping Weight, (Export) 1200 lbs

JKO HM-4 HAUNCHER $5,000

JKO HM-4 HAUNCHER $5,000

This HM-4 sports a 5 hp motor, an 1-1/4″ spindle, and 5-1/4″ under the nut. Max part thickness is 6-3/4″ while the max stroke is 9-3/4″.  See below for full specs on this machine. This fully functional machine has been fully cleaned, checked, and is ready to work from the time you receive it. This is our guarantee to both you and your company!

  • Maximum Spindle Capacity (Under the Nut): 5-1/4″
  • Spindle Diameter: 1-1/4″
  • Main Motor: 5 HP, 230/460v, 3ph
  • Table Size: 12″ x 24″
  • Pneumatic Dual Hold-Downs
  • Pneumatic Cycle w/ Foot-Pedal Control
  • Manual Hand-Crank for Table Adjustment
  • Maximum Stroke: 9-3/4″
  • Maximum Part Thickness: 6-3/4″
  • Maximum Cutter head Diameter: 9-3/4″
  • Cutter-head Speed: 5,600 RPM
  • Complete “like NEW” tooling pictured

VIRUTEX ROUTER FOR CONNECTORS AB181 $400

VIRUTEX ROUTER FOR CONNECTORS AB181 $400

This Vitutex AB181 is like new and was only used a handful of times. Price includes UPS shipping and insurance with in the continental US.  This fully functional machine has been fully cleaned, checked, and is ready to work from the time you receive it. This is our guarantee to both you and your company!

Router for placing connectors for detachable or fixed assemblies.

Machine specially designed for trimming the slots to place the OVVO® automatic connectors for assembling panels. Easy to use it makes the trimming fast and accurate. (Patented model)

 

Powerful 1000 W motor with electronics for speed adjustment and to keep the speed constant under load.

Positioning of the machine by mean of retractable stoppers and visual references.No need to take measures.

Adjustable fence for trimming in several angles. Automatic stoppers for 0°, 45° and 90°.

Precise adjustment of the panel thickness.

Precise adjustment of the trimming depth.

Fast trimming depth adjustment for several dimensions of the connectors. No tools or other machine adjustments needed.

Non-slip double base with non-scratch protection.

Dust collector nozzle. For a connection to an external dust collection.

 

 

conectores_3
New OVVO® assembling system

(Patented)

The OVVO® connection system saves assembling time and allows to transport the furnitures in flat parcels, saving time and volume. It is not necessary to use tols, screws or glue to assembly the pieces. The OVVO® system is a solution to join two pieces easily without to use traditional systems.

 

Invisible and detachable. Joints without glue

Very easy operation. Just press both pieces to be assembled, with the connector aligned, until to hear a “click”. The assembly is done.

It is an invisible solution, with a internal automatic clamp, that creates a perfect union between the two assembled pieces.

 

The OVVO® connectors system allows a variety of joints and angles

conectores_2

 

 

 

Specifications
Input power 1000 W
No-load speed 14000-27000/min
Chuck collet 8 mm
Weight 3,6 kg

EKSTROM CARLSON NO 112A DOUBLE SIDED OSCILLATING EDGE SANDER $3,500

EKSTROM CARLSON NO 112A DOUBLE SIDED OSCILLATING EDGE SANDER $3,500

Clean strong running double sided edge sander. 58” x 9” platens with good graphite installed. 60” x 11” tilting side tables. 27” x 20” tilting end table. 5 HP, 220/440V, 3 phase, 1740 RPM direct drive sanding motor.. ½ HP, 220/440V, 3 phase oscillation motor. Machine is currently wired 220V/3 Phase. This fully functional machine has been fully cleaned, checked, and is ready to work from the time you receive it. This is our guarantee to both you and your company!

WHIRLWIND MODEL 700 PROFILE SANDER $1,000

WHIRLWIND MODEL 700 PROFILE SANDER $1,000

Simple, single spindle, profile sander powered by a 1 HP single phase 120V motor featuring variable speeds of 0-1,800 RPM. The motor tilts 90 degrees while the 1-1/4″ diameter arbor can accommodate wheels up to 2-1/2″ thick. The table measures 27″ x 25″ x 34-1/2″ high. This fully functional machine has been fully cleaned, checked, and is ready to work from the time you receive it. This is our guarantee to both you and your company!

STENNER VHM 36″ RESAW W/HYDRAULIC FEEDER $12,500

STENNER VHM 36″ RESAW W/HYDRAULIC FEEDER $12,500

What can make a Stenner even better? How about a 5 HP hydraulic feeder! This Stenner VHM features 36″ Diameter wheels. A maximum sawing height of 16″. 4-3/4″ clearance to the left of the blade, and 7-5/8″ clearance to the right of the blade. The maximum width of saw blade is 4″ while the minimum width of Saw blade being 2″. The hydraulic pump allows for variable feed speeds from barely a crawl to screaming fast. This VSM is powered by a 25HP (18.5 kW) Main Motor. Net weight of machine 4170 lbs. All 4 felts oiling pads, along, with brass scrapers, and tubing are brand NEW. Machine also comes with 6 blades. This fully functional machine has been fully cleaned, checked, and is ready to work from the time you receive it. This is our guarantee to both you and your company!

SCMI MINIMAX FORMULA ME 30 EDGEBANDER $9,000

SCMI MINIMAX FORMULA ME 30 EDGEBANDER $9,000

Another clean small shop, Mom and Pop only run machine (literally)! This is an automatic edgebander with a glue pot to edgeband, with great flexibility, melamine edges, PVC and ABS up to 3 mm, and wooden strips up to 5 mm. This fully functional machine has been fully cleaned, checked, and is ready to work from the time you receive it. This is our guarantee to both you and your company!

Specifications:

  • On-Step adjustment for panel thickness with digital indicator
  • Feed track slides on two round guides for entire length, assuring a straight cut and resistance against side pressure load
  • Automatic Feeder for rolled edges and shear device for cutting thicknesses up to 3mm
  • Guide for feeding wood and laminate strips
  • Glue Pot is Teflon coated to facilitate easy glue change and cleaning
  • Automatic Thermostat on glue spreader
  • Device for automatic recovery of unused glue
  • Horizontal pressure unit with two rollers of which the first is power driven, both are equipped with mechanical pressure adjustments
  • High-frequency front and end cutting saw blade
  • Quick change trimming units with high frequency motors
  • Shaper cutters with replaceable insert tooling
  • Scraping unit
  • Buffing Unit
  • Telescopic support bar with rollers
  • Safety sound hood
  • Centralized dust collection
  • Panel thickness range 0.3-1.5″
  • Banding Thickness PVC/Wood 3mm/5mm
  • Min. Working Width 2.37″
  • Min. Working Length 5.5″
  • End cutting motors 0.3 HP @ 12,000 RPM
  • Edge trimming motors 0.4 HP @ 12,000 RPM
  • Edge trimmer cutting angle 12 degrees
  • Conveyor motor 0.8 HP
  • End cutting blade diameter 100 mm
  • Weight 1,249 LBS

 

BLACK BROS 60″ PINCH ROLLER $3,500

BLACK BROS 60″ PINCH ROLLER $3,500

This is a heavily built 62″ (actual) Black Bros pinch roller. It’s power by a 1.5 hp 110/220V single phase motor. It features 8.5″ diameter rolls and has a 5″ daylight opening. The rolls are in good shape. This fully functional machine has been fully cleaned, checked, and is ready to work from the time you receive it. This is our guarantee to both you and your company!

PRESTO 47″ X 57″ 2,000 LB LIFT TABLE $1,250

PRESTO 47″ X 57″ 2,000 LB LIFT TABLE $1,250

This is a Presto Model XL24-20-MOD 2,000 lb capacity lift table. It is powered by a 1.5 HP 208-230V/3 phase hydraulic power pack. The original top size was increased from 36″ X 36″ to the current 47″ X 57″. It has a lowered height of 7″ and a raised height of 32″. The safety curtains do have tares and are also easily removed if un-needed. This lift table underneath the curtains is in excellent condition and the machine is pendant controlled. This fully functional machine has been fully cleaned, checked, and is ready to work from the time you receive it. This is our guarantee to both you and your company!

2013 HOLZ-HER ARCUS 1334 (SERVO) EDGEBANDER W/2,600 HOURS $39,500

2013 HOLZ-HER ARCUS 1334 (SERVO) EDGEBANDER W/2,600 HOURS $39,500

Clean loaded Holz-her 1334 with all the options like pre-mill and 4 motor corner rounding. Machine currently has a little over 2,600 run hours on it. Very clean hard to find, low hour machine that easily powers thru edge-banding like 3 mil and strips. This machine also has hoppers for cartridge and granules. The GlueJet technology will allow for the use of not only granules and cartridges, but GlueJet PUR as well. With no glue pot, color change overs are fast, simple, clean, and waste little glue. 15″  EdgeController Screen. 1802 Pre-Milling Servo Infeed Fence,  1901 Edge Feed Snychro, Automatic Feed Magazine GJ301 Automatic GluJet Pressure Section, 1914 Pressure Unit Pneumatic Driver (servo), 1925 End Trim Unit Top/Bottom Trim (2 servos), 1828 Top and Bottom Cutter, 1833 Profile Cutter Corner Rounding Unit (4 servos), 1927 HD Profile Scraper (1 servo – in/out), 1964 Finish Scraper, 1944 Top and Bottom buffing unit. A full set of manuals also accompanies this machine. This fully functional machine has been fully cleaned, checked, and is ready to work from the time you receive it. This is our guarantee to both you and your company! This machine is stored in our warehouse. Give us a call to schedule a demo!

***Stations read the following from left to right on the Edgecontroller GJ301, Beam, Feed-V, 1802, 1901, 1901, 1914, 1925, 1925, 1828, 1833, 1927, 1964, 1944 (duplicates mean that you have multiple options for that given station) Machine replacement cost $150,000

OAKLEY H5 OSCILLATING EDGESANDER $3,300

OAKLEY H5 OSCILLATING EDGESANDER $3,300

This is a really nice example of an Oakley H5 sporting it’s original paint. Flat 9″ x 58″ cast iron platens with NEW graphite. 8″ x 164″ Abrasive Belt Size. 11″ x 62″ adjustable height/tilting side table. 22″ x 44″ adjustable height/tilting end table. 7.5-HP main motor. 1/2 HP oscillation motor. 220/440/3 Phase. 140 oscillations/minute and a 1/2″ oscillation movement. This fully functional machine has been fully cleaned, checked, and is ready to work from the time you receive it. This is our guarantee to both you and your company!

BLACK BROS 56″ BOTTOM ONLY GLUE SPREADER $5,000

BLACK BROS 56″ BOTTOM ONLY GLUE SPREADER $5,000

This Certified Pre-owned Black Bros glue spreader is clean where it counts. The 8″ diameter X 56″ wide rolls are clean and glue free. At some point the doctor rolls were re-chromed and there is a good set of ends seals on this machine. Maximum daylight opening is 4-1/2″. This machine is powered by a 220/440V/3 Phase 1-1/2 hp motor featuring forward and reverse. This fully functional machine has been fully cleaned, checked, and is ready to work from the time you receive it. This is our guarantee to both you and your company!

BLACK BROS SIDE LOADING 5’X10′ ADJUSTABLE OPENING COLD PRESS $22,500

BLACK BROS SIDE LOADING 5’X10′ ADJUSTABLE OPENING COLD PRESS $22,500

This side loading Black Bros cold press features a 5′ X 10′ (62″ X 122″ actual) capacity with up to a 42″ daylight opening (manually adjustable). The top is comprised of 3 plates. One 24″ plate to the left and twin 48″ plates to the right. They can be used independently or in conjunction with one another.  Plates are flat and dent free. The press is powered by 36 pods and also features pop up rollers built into the bottom for ease of loading and unloading. All six of the Ross Control Valves, which are the main controls, have been rebuilt along with all three main regulators. This fully functional machine has been fully cleaned, checked, and is ready to work from the time you receive it. This is our guarantee to both you and your company! This machine is stored in our warehouse. Give us a call to schedule a demo!

BLACK BROS SIDE LOADING 5’X10′ MOTORIZED ADJUSTABLE OPENING COLD PRESS $27,500

BLACK BROS SIDE LOADING 5’X10′ MOTORIZED ADJUSTABLE OPENING COLD PRESS $27,500

This side loading Black Bros cold press features a 5′ X 10′ (62″ X 122″ actual) capacity with a 40″ motorized daylight opening. The top is comprised of 3 plates. One 24″ plate to the left and twin 48″ plates to the right. They can be used independently or in conjunction with one another.  Plates are flat and dent free. The press is powered by 36 pods and also features pop up rollers built into the bottom for ease of loading and unloading. This fully functional machine has been fully cleaned, checked, and is ready to work from the time you receive it. This is our guarantee to both you and your company! This machine is stored in our warehouse. Give us a call to schedule a demo!

MCKNIGHT MILLER DOUBLE END/DOUBLE STATION HAUNCHER $8,000

MCKNIGHT MILLER DOUBLE END/DOUBLE STATION HAUNCHER $8,000

This is a very hard to find machine and is really 2 machines in one. First off it can be used as a double end hauncher. However it can also be used as two separate haunchers as well via the flip of a switch. So you have the option for both heads to be controlled and cycled at the same time or you can opt to literally use each head by itself independently from the other. Please see below for full specs. This fully functional machine has been fully cleaned, checked, and is ready to work from the time you receive it. This is our guarantee to both you and your company!

Maximum Length:       93″ center to center of the arbors (you could also gain possibly 12″  by moving the fixed head if needed as well)

Minimum Length:       15″ center to center of the arbors

Cutter Motors:              10 HP Each 208-230/460V/3 Phase

Spindle Speed:              4,200 RPM

Spindle Diameter:       1-1/4″

Max. Cutter Dia. :        7-1/4″

Max. Cutter Length:   5-1/4″

Max. Stroke Length:  9-1/2″

Stroke Speed:              Hydraulically Dampened/ Infinitely Adjustable

Table Adjustment:     15 Degrees up/5 Degrees Down

Table Adjustment:     1″ In & Out

Cycle:                            Foot Pedal (2)

***INSERT TOOLING INCLUDED PER PICTURES

CONQUEST M23 CONSTRUCTION BORING MACHINE $2,750

CONQUEST M23 CONSTRUCTION BORING MACHINE $2,750

These are simple, but robust, machines and because of that they are also easy to set up and extremely accurate. This 23 spindle dedicated horizontal head construction drill has 23 spindles on 32 mm centers. It features left and right fences, a flip up back fence, and a 45 degree plate that bolts into the center of the machine table. The machine features dual hold downs and it is powered by a 208-230/460V/3 Phase Baldor motor. This fully functional machine has been fully cleaned, checked, and is ready to work from the time you receive it. This is our guarantee to both you and your company!

Standard Features & Specifications

  • Working table height of 37.5”
  • 2 Pneumatic hold downs
  • Pneumatic foot pedal operation
  • Operating pressure of 80-100 psi
  • Motor turns off when pedal released
  • 23 – spindle head(s) heat treated steel helical gears
  • 32 mm centers, dist. between first & last drill = 28.5”
  • Baldor motor(s) 3,450 rpm 208-230/460V/3 Phase Baldor Motor
  • Accepts 10 millimeter flat shanks bits, 12 lefts & 11 rights (per head) – (Maximum Drilling Distance from edge of board with Optional Vertical head is 3.5”)
  • Machine weight (approx..) 1,110 lbs., crated 1,175 lbs. Footprint: 32” wide X 40” deep

WYSONG & MILES NO. 303 COMBINATION DISK AND OSCILLATING SPINDLE SANDER $2,500

WYSONG & MILES NO. 303 COMBINATION DISK AND OSCILLATING SPINDLE SANDER $2,500

This machine is two in one. It features a 26″ disk sander with a 15″ X 34″ titling table (to 45 degrees) on one side. On the other you will find an oscillating spindle sander featuring a 24″ X 24″ tilting table (15 degrees forward and 35 degrees backward) with a 2″ X 8″ oscillating spindle. Power for each is provided via a 5 hp motor. A swing out arm holds a 2 gallon bucket to the side of the machine for small parts or waste. Machine is 220V/440V/3 Phase. The only repair we see is a braze on the motor mount which is a very old repair and does not effect machine operation. This fully functional machine has been fully cleaned, checked, and is ready to work from the time you receive it. This is our guarantee to both you and your company!

NEW OLIVER 22″ or 25″ PLANER W/BYRD HELICAL HEAD

NEW OLIVER 22″ or 25″ PLANER W/BYRD HELICAL HEAD

$$$CALL FOR THE MOST COMPETITIVE PRICING YOU WILL FIND$$$ We also carry Oliver’s full line! Contact us for a quote today on any machine they offer!

Choose between the following models:

4455.103B 22″ Planer W/ Byrd Shelix Cutterhead 7.5 HP 1 Phase

4455.104B 22″ Planer W/ Byrd Shelix Cutterhead 10 HP 3 Phase

4470.101B 25″ Planer W/ Byrd Shelix Cutterhead 10 HP 1 Phase

4470.102B 25″ Planer W/ Byrd Shelix Cutterhead 15 HP 3 Phase

4470 25” PLANER

The Oliver 4470 25” Planer puts other planers to shame. With two full feet of cutting width, over 9” of cutting capacity, and the ability to take up to 1/4” off in a single pass, this planer will take whatever you can dish out. The digital thickness controller and powered table travel eliminate guesswork, make dialing in settings a breeze. But ease of operation isn’t everything, this Oliver outputs stock that’s smooth and straight. A sectional infeed roller and chip breaker apply uniform pressure on uneven stock, coupled with two outfeed rollers to keep your stock in place. Add plenty of power under the hood, and you’ve got a planer that’s ready to tackle anything!

  • Available with three styles of a cutter head, straight, helical, or authentic BYRD.
  • Helical carbide inserts are indexed for quick changing.
  • Massive cast iron construction throughout allows up to a 1/4” cut.
  • Polished built-in table roller assists movement of rough stock.
  • Segmented infeed roller and sectional chip breaker easily handle rough stock.
  • Dual outfeed rollers assist with heavy stock.
  • 3-speed gear box provides the perfect feed rate.
  • Magnetic controls with emergency off switch for safer operation.
  • Control panel with digital readout allows precise thickness settings.
  • Power assisted table makes for quick, accurate, adjustments.
  • Hinged access to cutter head and feed rollers for quick set-up.
  • 5” dust chute easily handles chip removal.
  • Easy access to motor, drive train, and gearbox assist in maintenance and adjustment.
  • Powerful TEFC motor available in single or three-phase.
  • *Optional 440/460 volt available special order only. Additional cost/parts may apply.
    Model No.
    4470
    Stock No. (10HP, 1Ph, Straight)
    4470.001
    Stock No. (15HP, 3Ph, Straight)
    4470.002
    Stock No. (10HP, 1Ph, Helical)
    4470.1014S
    Stock No. (15HP, 3Ph, Helical)
    4470.1024S
    Stock No. (10HP, 1Ph, Byrd)
    4470.101B
    Stock No. (15HP, 3Ph, Byrd)
    4470.102B
    Maximum Stock Width
    25”
    Maximum Stock Thickness
    9-1/4”
    Minimum Stock Thickness
    1/8” Manual – 15/64″ Automatic
    Minimum Stock Length
    10”
    Dust Port Diameter
    5″
    Minimum CFM Required
    900 CFM
    Infeed Roller Diameter
    3”
    Steel Outfeed Roller Diameter
    3” (x2)
    Feed Speeds
    20, 25 and 30 FPM
    Bed Rollers
    2, Adjustable
    Table Size
    32” L x 26” W
    Footprint
    47-1/2” L x 21” W
    Cutterhead Diameter
    3-3/8”
    Number of Knives (straight)
    4
    Number of Knives (helical)
    174-4S (125-Byrd) (102-30mm)
    Cutterhead Speed
    4,800 RPM
    Table Support
    2-Column
    Motor (1Ph)
    10HP, 240V Only (43 AMPS)
    Motor (3Ph)
    15HP, 240V/440V, Prewired 220V (37 AMPS, 220V 3Ph) *Optional 440/460 volt available special order only. Additional cost/parts may apply.
    Overall Dimensions
    46” L x 23” W x 56” H
    Net Weight
    1,775 lbs
    Gross Weight
    1,837 lbs

TRIAD SSR CNC SMART STAIR  ROUTER / TRENCHER $22,500

TRIAD SSR CNC SMART STAIR  ROUTER / TRENCHER $22,500

NEW ARRIVAL AND VERY HARD TO FIND!

Pictures of screen shots show just how easy it is to use!

This is a CNC controlled Smart Stair Router. This is not a template machine! Operators can load 2 x 10 or 2 x 12 stringers, enter menu driven parameters with a state of the art touch screen monitor, and press “Run”. The SSR does the rest. Two heavy duty routers will cut the top or bottom stringer only or both stringers simultaneously with the specified profile. It will automatically index the material the proper distance, the appropriate number of times, and do it again and again. It can accommodate standard stair profiles, no-riser profiles, and split stringer configurations, open stringer. User configured hard or soft wood selections automatically adjust the router feed rate to maximize performance. (2) heavy duty 2 HP belt driven routers with 1/2″ collets. Two stepper linear actuators for cutting stair profiles; (1) servo/stepper drive wheel for material indexing; 628 lb vertical clamp and 352 lb horizontal clamp; industrial computer; 3.5″ floppy drive and 10-1/2″ color touch screen; coordinated 4-axis motion controller; tread – 8″ to 12-1/2″; riser – 5-1/2″ to 9″; nose clearance – 1/2″ to 3″; nose extension – 1/2″ to 2″; tread thickness – 1″ to 1-3/4″; stringer material – 2″ x 10″, 2″ x 12″, 3/4″ x 10″, and 3/4″ x 12″; no riser – Menu selectable bit size allows you to enter your exact tooling size – 7/8″ diameter straight flute RH or LH; air supply – 100 psi, 1/2″ dedicated line.  Dimensions: 7′ wide x 7′ long x 6′ high; Machine weight: 1,200 lbs. This fully functional machine has been fully cleaned, checked, and is ready to work from the time you receive it. This is our guarantee to both you and your company!

NEW JOOS HOT PRESS

NEW JOOS HOT PRESS  Contact us for a quote today!

We have seen a lot of presses. If we had a choice we would buy Joos and Joos alone. We choose Joos because of the stellar service and support Joos USA offers in addition to the the quality of every component on a Joos press. From the quality of the actual steel that makes the frame to the placement of supports. Hi end/no compromise components and engineering can be found through-out their products. You get gold anodized platens and features like their patented ABS that all but eliminates pressing incorrectly loaded or forgotten parts. Did we mention the Elkom platens! You can also choose between glycol/water, electric, or oil heated platens. Electic plates to 425 degrees (working) Fahrenheit,  high pressure plates that can reach 300 degrees Fahrenheit plus or minus 1 degree or oil plates up to 800 degrees.  One thing that is often over looked is the quality of their heaters. They offer the most stable temperatures with the minimum energy consumption. Contact us for a quote today.

BAURLE SFM DOUBLE SPINDLE SHAPER $1,750

BAURLE SFM DOUBLE SPINDLE SHAPER $1,750

This is a bit of a rare machine in both existence and how cutting edge it was for it’s time. This one sports 1-1/4″ spindles with 5-1/2″ under the nut. It is powered by twin 3/4 KW multi speed spindle motors. Meaning either 3 KW or 4 KW depending on speed. Making it either 4 or 5 hp. Speeds of 2800-4500-5600-6000-9000-12,000 RPM can be achieved via a combination of belt swapping and choosing the proper motor speed of high or low. This machine does feature clockwise and counter clockwise rotation as well as spindle locks. The brakes are incomplete and do not function. Table Size is 79” x 36”. This particular machine is clearance priced to make room for new inventory.

****This machine is non-returnable and does not have a warranty. While it is strong running it is not perfect and is priced accordingly.

EKSTROM CARLSON DOUBLE SPINDLE SHAPER $1,750

EKSTROM CARLSON DOUBLE SPINDLE SHAPER $1,750

This double spindle shaper sports twin 6″ long X 1-1/4″ spindles. It is powered by a pair of 5 hp motors that both have working short stop brakes. The table top measures 38″ X 62″. This particular machine is clearance priced to make room for new inventory.

****This machine is non-returnable and does not have a warranty. While it is strong running it is not perfect and is priced accordingly.

DOUCET FEEDBACK 36 RETURN CONVEYOR $5,750

DOUCET FEEDBACK 36 RETURN CONVEYOR $5,750

Fully functional Doucet Feedback 36 with all NEW round belting installed. You have a 36″ x 3′ receiving conveyor with a 36″ x 11′ return conveyor. That 11′ equates to 8′ of return in front of  your machine. This machine is designed for shape and sand machines , small edge banders, edge foilers…….ect…… The feed rollers, driven by a D.C. variable speed motor which guides the part onto the receiving module. Polymer belts side shift the panels to the return rollers quickly and efficiently. The transfer process occurs on a continuous basis. The power requirments for this machine are simply 115V. This fully functional machine has been fully cleaned, checked, and is ready to work from the time you receive it. This is our guarantee to both you and your company!

WYSONG & MILES/CENTRAL MACHINERY 600 AND 601 DOVETAIL MACHINES $12,500

WYSONG & MILES/CENTRAL MACHINERY 600 AND 601 DOVETAIL MACHINES $12,500

Don’t let these pass you by as these are the cleanest Central Machinery 600 & 601’s that we have seen! Seriously look at the amazing condition these are in! Wysong built really robust and reliable dovetail machines back in the day. Fast forward a few decades and you will find this 600 & 601 that were rebuilt by Central Machinery (these are the ones you want) out of Lexington, North Carolina at some point. So what does rebuilt mean? It means they were brought up to spec and modern standards and are better than the original versions in many ways. You will find New bushings, bearings,  motors, controls, starters, fuses, control boxes……machines are totally re-wired with liquid tight conduit…….the air system is completely redone from piston seal and fitting to plumbing and air regulators/oilers………….even the oil strainers were replaced. These machines are fast, durable, and able to machine 2 parts at once. The “tail” machine (600) has only one fence because you stack you parts……face to face and in a matter of seconds you have a pair of tails. The “pin” machine (601) works a little differently in that you have a left and right fence. By placing a board both left and right you produce a pair of pins in a matter of seconds. These machines have 15 spindles on 1″ centers. Very simple and efficient. So if you can live with the limitation of 15 spindles……….or 15″ of width……on one inch centers dovetails will be a breeze! The only other downside is they tend to be loud. However within their limitations they are far far faster than CNC dovetail machines. Other features include built in oilers for the spindles, variable speed (cycle time), and Accurate Technologies Pro-Scale on the 600. These fully functional machines have been fully cleaned, checked, and are ready to work from the time you receive them. This is our guarantee to both you and your company!

WEINIG RONDAMAT 925 PROFILE GRINDER $4,250

WEINIG RONDAMAT 925 PROFILE GRINDER $4,250

This Rondamat 925 features a 1-1/2″ diameter X 9-1/2″ arbor length with a 9″ maximum tool diameter. It’s powered by a 1.5 HP Motor 220/440V/3 phase. 8-7/8″ maximum wheel diameter and variable grinding wheel speeds: of 1,700, 2,000, 2,250, 2,800 RPM. Clearance Angle for Back Relief: 15 – 45 Degrees and an Axial of 0 – 10 Degrees.  Coolant pump and tray.  This fully functional machine has been fully cleaned, checked, and is ready to work from the time you receive it. This is our guarantee to both you and your company! note: arbor nut (m12 1-75) missing.

VOORWOOD GROOVE FOILER (P78 PLOUGH CUT FOILER)$12,500

VOORWOOD GROOVE FOILER (P78 PLOUGH CUT FOILER)$12,500

This is a very hard to find machine and it only has 1,403 hours. It features the following stations: Station 1: Score,  Station 2: Shape, Station 3 & 4 Sand, Stations 5 & 6 Finishing heads. This machine will cut a single plough (bluff cut) to the desired profile in a MDF drawer front or similar component, then sand and apply transfer finish to the plough, all in one pass. Additionally you will receive spare tooling (several profiles), wheels, dust manifold ect. per pictures.  This fully functional machine has been fully cleaned, checked, and is ready to work from the time you receive it. This is our guarantee to both you and your company!

  • Pattern changeover accomplished in minutes
  • Equipped with climb-cut scoring
  • Shape station incorporates an electronically balanced, precision spindle
  • After sanding, final finishing of the transfer process; no trimming
  • Accommodates a part width of 4″ plus width of edge profile to 48″ maximum
  • Accommodates a part .50″ – 1.75″ thick (1.936″ actual thickness)
  • Accommodates a depth of cut to .375″

 

DIEHL MODEL 890 VENEER SPLICER $7,500

DIEHL MODEL 890 VENEER SPLICER $7,500

We work hard to continually bring clean machines to the marketplace and this 890 is just that. 1/64″ Min. thickness capacity, 6″ min. length capacity, and a 42″ max. width to right capacity. Upper & lower feed chains. 1.5 HP Variable speed feed motor with variable feed rates of 15 – 85 FPM. (4) roller matching in feed roll assembly. Thin veneer pressure bar package with powered out feed roll group. Includes several spare heating elements. This fully functional machine has been fully cleaned, checked, and is ready to work from the time you receive it. This is our guarantee to both you and your company!

ROSENQUIST EB750H45 FEED THRU RADIO FREQUENCY PRESS $24,000

ROSENQUIST EB750H45 FEED THRU RADIO FREQUENCY PRESS $24,000

This is a really nice size feed thru press featuring a plate area of 54″ x 90″ and a pressing area of 58-1/2″ X 96″. Ideal for 2 step process for 15’0″ product. Max thickness capacity is 4-1/2″. It is powered by a 20 KW RF Generator while pressing is handled by a 10 HP hydraulic pump. There are a total of 20 cylinders. 15 for edge pressure and 5 providing top pressure. All 20 cylinders have been rebuilt. The 98″ in-feed table features a hydraulic feed and there is also a matching  98″out-feed table to maximize loading and unloading. This fully functional machine has been fully cleaned, checked, and is ready to work from the time you receive it. This is our guarantee to both you and your company!

COSMA 1300/30 TWO HEAD OSCILLATING 51″ BRUSH SANDER $9,000

COSMA 1300/30 TWO HEAD OSCILLATING 51″ BRUSH SANDER $9,000

This two head oscillating brush sander is designed to finish sand and sealer sand work pieces such as raised panel doors, entry doors, louvers, shutters, panels etc. This machine features a 51″ width capacity and a 2″ thickness capacity. The current set of Edruflex abrasives (both 180 grit) are like new and have 90% or better life left in them. It features 3.5 hp motors on each head and a 1 hp motor on the conveyor. All three have variable speed with digital read outs.  The vacuum bed is powered by a pair of 3 hp blowers built in under the conveyor. While the height adjustment is motorized. Everything on this sander functions as it should. This fully functional machine has been fully cleaned, checked, and is ready to work from the time you receive it. This is our guarantee to both you and your company!

MEREEN JOHNSON NO 435-H 60″ GANG RIP SAW $18,000

MEREEN JOHNSON NO 435-H 50″ GANG RIP SAW $18,000

This is something you rarely see come to market. If you process a lot of sheets goods into strips look no further because wide gang rips are few and far between. With a 50″ wide x 2-1/2″ maximum thickness capacity (& 60″ long arbor) panels are cut into strips using 12″ maximum diameter tooling. The 50″ wide feed bed consists of aluminum slats with replaceable steel-backed rubber insert strips (Merreen Johnson has quoted us $5,400 for the inserts & hardware if you wish to replace). The feed bed is arranged for friction feeding, with dip at the saw line to allow infinite saw spacing on saw arbor without contacting the feed bed. Precision feed sprockets with hardened teeth. Feed system with oil mist lubrication of bottom chain surface and extended pins on chains including automatic low oil and air supply level control, system shut-off feed drive motor to prevent running machine without proper lubrication. A 4 HP variable speed feed drive with manual adjustment with feed rates from 20 to 75 FPM. The 75 HP saw arbor measures 2-5/8″ in diameter and is 60″ in length. Upper in-feed pivoting anti-kickback assemblies are provided for operator safety. You will get a total of 22 ten inch blades with an arbor size of 3-1/2″ and also included are 10 blade collars. This fully functional machine has been fully cleaned, checked, and is ready to work from the time you receive it. This is our guarantee to both you and your company!

BLACK BROS 26″ TOP AND BOTTOM GLUE SPREADER $12,500

BLACK BROS 26″ TOP AND BOTTOM GLUE SPREADER (Direct & Reverse Head Options) $12,500

This is Black Bros heavy duty model (Sporting 8″ Rolls) and not to be confused with it’s lighter sibling! It is well optioned and in excellent condition especially for a glue spreader. It can handle material up to 6″ thick, but it also excels in laying a precision layer of glue on the top as it features the “Reverse Roll Filling Top Head Configuration” where as there is a chrome doctor roll on each side of the applicator roll. One to set the glue line with the applicator roll (meaning it indexes off the applicator roll itself) and the other to remove any excess glue to guarantee uniform thickness (meaning it indexes off the substrate and has vertical adjust-ability off the top of the substrate glue is being applied too). This gives amazing results especially on thinner materials or where a precise glue line is required. Additionally you can disengage the second doctor roll and use it as a traditional “Direct Coating Configuration” machine. The lower roll features a “Direct Coating Configuration” meaning a roll and traditional single doctor roll. Variable speed of 40-120 FPM via Twin 1-1/2 hp Reeves drives.  Full length operating control bars on both sides offer convenient machine control for forward, reverse, and emergency stops. This machine is also equipped with a pneumatic spray bar for ease of cleaning and flushing of the machine. This fully functional machine has been fully cleaned, checked, and is ready to work from the time you receive it. This is our guarantee to both you and your company! note: no end seals on bottom heads.

TYLER SIDE LOADING 75″ X 114″ MOTORIZED ADJUSTABLE OPENING COLD PRESS $22,000

TYLER SIDE LOADING 75″ X 114″ MOTORIZED ADJUSTABLE OPENING POWER POD COLD PRESS $22,000

Very well maintained Tyler 80 PSI pod press with a 75″ deep X 114″ wide capacity and a 60″ daylight opening. This press features 3 upper platens measuring 38″ X 75″ each. Each platen contains 3 rows of pods wide that are 6 deep for a total of 18 pods each platen or 54 total pods for all 3 platens. Each platen has 3 zones. You can choose to use the 2 center rows only for a 3′ X 2′ zone per platen, the 4 center rows for a 3′ X 4′ zone per platen, or use all 6 rows for a 3′ X 6′ zone (38″ X 75″ actual). The bottom of the press contains spring loaded pop up rollers for ease of loading and unloading. This fully functional machine has been fully cleaned, checked, and is ready to work from the time you receive it. This is our guarantee to both you and your company!

WEINIG UNIMAT STAR 1000 MOULDER 8,000 RPM W/950 GRINDER + TOOLING

WEINIG UNIMAT STAR 1000 MOULDER 8,000 RPM W/950 GRINDER + TOOLING & MORE $$$RECENTLY SOLD$$$

This 2004 moulder has everything going for it. From how well maintained and clean it is to it’s completeness. It also shows moderate usage at best for a 1000! B-R-L-T-T-B 8,000 RPM spindle configuration, beautiful bed plates, Rondamat 950 Grinder (very complete), Weinig Memory System for fast change overs, Manuals for everything, 17 heads, set up stand,  268 sets of knifes and templates PLUS everything you see…….Waxlit…..coolant…spacers….wrenches….manuals! Ask yourself this, “When is the last time you saw something this clean and complete?” A really nice package to say the least! This fully functional machine has been fully cleaned, checked, and is ready to work from the time you receive it. This is our guarantee to both you and your company!

Need that machine with higher rpm for a faster run , this is the best with 1 13/16″ spindles.

Spindle configuration: B-R-L-T-T-B

Working dimensions: 6″ x 9-1/16″

Motors: B-10 HP, R-15 HP, L-15 HP, T-25 HP, T-20 HP and B-20 HP.

Spindles: 1-13/16″ with rebate cutter first bottom at 6,000 rpm; Spindles 2-6 8,000 RPM. Electronic readouts all spindles. Chipbreakers and pressure elements with LED readouts.

Feed: 7.5 HP motor with feed speed from 20-118 FPM. Variable speed with invertor drive

CNC: WEINIG “Memory Redial” Profile and tool data management; Exports tool data to the readouts for quick setting.

Tables/Fences: Infeed table 6’6″ with lateral pressure roller: chromed tables and fences: Powered rollers between top heads and at outfeed full width.

Includes: Manual table lubrication; central lubrication. Lights inside enclosure. Heads included.

RITTER R-30 TRIPLE SPINDLE DOOR SHAPER $6,500

RITTER R-30 TRIPLE SPINDLE DOOR SHAPER $6,500

This is a Ritter R-30 which has 3 shaper spindles mounted in a common base with a 38″ x 64″ worktable. Designed for running raised panels, style & rail material, and tenons for raised panel doors. Equipped with 1-1/4″ diameter spindles. Spindles are powered by (1) 7.5 HP motor & (2) 5 HP motors. All motors are Baldor 208-230/460V/3 Phase. Includes air tenoning jig. This fully functional machine has been fully cleaned, checked, and is ready to work from the time you receive it. This is our guarantee to both you and your company!

WEINIG UNIMAT 500 MOULDER $$$SOLD$$$

WEINIG UNIMAT 500 MOULDER $$$RECENTLY SOLD$$$

This is not the cheapest 500 nor the most expensive one out there. It is however the cleanest and lowest hour Unimat 500 you will find. Used very sparingly for short run work! All you have to do is pop the hood and you can see that this is a well maintained low use machine. Note: Machine comes with a total of 8 heads. (5 are in the machine) This fully functional machine has been fully cleaned, checked, and is ready to work from the time you receive it. This is our guarantee to both you and your company!

Spindle configuration: B-R-L-T-B

Motors: Bottom 10 HP, right/left 15 HP, top 15 HP, bottom 10 HP motors, with mechanical brakes.

Spindles: Dia. 1-1/2″ with cutterhead speed of 6,000 RPM. Electronic LED readouts for all tool holder settings, including chipbreakers & pressure elements. Receding chipbreaker & pressure element at top spindle;

CNC: PowerCom Plus software system:  Features, profile drawing storage, profile dimensions, tool changes and production optimization. Motorized positioning Radial on spindles 2-5.

Feed system: Inverter controlled, variable from 18 – 100 FPM –  4 HP motor.

Tables: Infeed straightening table 2 M (6-1/2′), central lubrication, lateral pressure roller mounted at infeed table. Full sound & safety enclosure with electro-mechanical interlock and automatic table lubrication pump.

2014 TIMESAVERS PUMA 3 HEAD WET 52″ WIDE BELT SANDER

2014 TIMESAVERS PUMA 3 HEAD WET 52″ WIDE BELT SANDER GRINDER DEBURRING/FINISHING METAL/SOLID SURFACE $$$RECENTLY SOLD$$$

This is truly a rare find. You simply don’t find machines (especially wet) for nearly 70% off the NEW cost with such low hours. This is a 3 head 52″ wide machine with an air knife for drying your parts as they exit the machine.  This PUMA series sander has under 205 hours of total use and a replacement cost of nearly $200,000 in today’s market. The Puma Series machines require minimum maintenance and up keep, and both sides are easily accessible by operators. Ideal for deburring and finishing in a production setting and for 24/7 operations.

Abrasive belt size: 52” x 75”
Main motors: 30, 30, 30 HP
Maximum width stock: 51”
Minimum part length: 10”
Maximum thickness opening: 0-6”
Infeed loading area: 27”
Feed speed: 5-20 FPM
Voltage/Phase/Frequency: 460/3/60
Approximate full load amps at 460 volt: 149
Motor type: TEFC
Passline height: 41”, Constant
Compressed air usage: 6 CFM @ 90 PSI
Approximate shipping weight: 12,500 lbs.
204 hours shown on meter

Equipped with three top heads, each being an 8” contact roll. It includes industry leading standard features, along with the optional features needed to meet your specific application needs. Here is why the superior design and construction of the PUMA gives you the competitive edge.

Contact Drums: (All 3 positions) 
The sanding heads include dynamically balanced 8” diameter contact drums with precision bearings. Hardness (durometer) and serration are chosen for general deburring and finishing applications.

Main Motors: 
All abrasive head drive motors and feed drive motor are precision balanced for power and long life. Motors are TEFC, Totally. Enclosed Fan Cooled for durability.

Cam Adjustable Contact Drums: 
Adjustable contact drums allow fine-tuning of abrasive belt pressure on parts without the need to adjust holddown rolls. This also allows the possibility of running abrasive belts of different thickness without having to adjust holddown rolls.

Percentage Load Meters: 
A load meter on each abrasive head displays exact percentage of main motor horsepower being used during operation.

Through-Beam Abrasive Belt Tracking: 
Electronic photo-eye tracking monitors and controls abrasive belt movement on the grinding head. Over-travel limit switches prevent abrasive belt damage in case of mis-track.

Quick Release Outboard Support: 
Allows fast removal of outboard support to expedite abrasive belt change. Abrasive belts can be changed in as little as 60 seconds.

Dual Infeed and Dual Outfeed Holddown Rolls: 
Rubber-covered, spring-loaded rolls aid in holding sheet metal parts onto the conveyor as they pass through the machine. A sheet metal gate which acts as an emergency stop for the operator when loading the machine. The gate actuates a limit switch which shuts down the abrasive belt head and conveyor feed in emergency situations.

Variable Speed Conveyor Drive: 
5-20 FPM variable frequency conveyor drive includes an LED speed display.

Variable Passline Height: 0-6” bed opening capacity with a 41” conveyor passline height. 

Motorized Thickness Adjustment: 
Conveyor bed thickness setting is motor driven. This allows quick changes of thickness settings for material to be processed.

Electronic Digital Thickness Readout: 
An electronic thickness set-up device includes a “go-to” function with ability to store programs for ten thickness’. The readout also indicates conveyor bed position in relation to the grinding belt for accurate set-up to .001”
This system includes a high efficiency blower, precision top and bottom air knives and rubber squeegee rolls to remove excess coolant as parts exit the machine.

Air Operated Disc Brakes: 
Floating caliper disc brakes are used to stop the contact drum and brush head to assure consistent abrasive head stoppage in approximately four seconds. The braking system will not fade under continuous braking and has non-sparking, easily replaceable linings. The brake is located on the main motor shaft for easy maintenance.

Centralized Control Panel: 
Simple operator controls for machine operation. Conveyor feed, speed, coolant filtration, air knife dryer and abrasive heads are controlled at this centralized location.

Hour Meter: 
An hour meter displays actual running time of the machine. This unit is used by maintenance for scheduled lubrication of key components.

Lubrication System: 
Sanding head lubrication points are plumbed for easy access.

U.L. Listed Components: 
Includes main motor fusing, electrical disconnect, Star Delta starters and 110 volt controls.

2007 WEIMA WL 10/45 V-ROTOR GRINDER 51KW/68HP

2007 WEIMA WL 10/45 V-ROTOR GRINDER 51KW/68HP $$$RECENTLY SOLD$$$

This particular WL 10/45 was made on 09/2007 and has 5,934 hours on it. V-Rotor head has all NEW knives installed.  It also features the largest motor available on the WL10 and the head has the largest knife option with 52 total knives.  The “WL” shredder is designed exclusively for shredding wood/timber and similar materials e.g. plastics, cardboard, ect. Rotor speed 100 RPM. Main Motor 51 KW/68 HP. Hydraulic Motor 2 KW/2.5 HP. Rotor diameter 368 mm. Number of tools 52. Automatic Star-Delta starting. Vibration dampening feet. Very hard to find grinder! Price includes choice of screen (NEW) hole size. Choose between the following 20, 25, 35, 50, 75, or 150mm. OR choose to operate with out a screen and or fabricate your own to meet your needs for maximum output and take $2,000 off the list price. Machine is tuned up and ready to go, New set of 4 sided knives including hardware installed, several holders replaced, New bearings in Hydraulic motor, New hydraulic hoses, New lower gearbox seal, 3 New contactors, and paint touched up as needed.

 

2016 MARTIN T12 SHAPER & 4 ROLL POWERFEED W/34 HOURS

2016 MARTIN T12 SHAPER & 4 ROLL POWERFEED W/34 HOURS $$$RECENTLY SOLD$$$

Martin model T12 Shaper with under 34 total hours (absolute hour meter/not re-settable/hour meter runs when head is on only). This T12 Shaper is powered by a 5.5 kW (7.5 HP) motor with a 1-axis control and 5.7″ cutting height. Rotational speeds including forward and reverse and spindle speeds of 3,600 / 5,400 / 7,200 / 9,600 / 12,000 rpm by shifting the belt with belt quick-tensioning device. Left and right table extension on both sides, with extendable work piece support. Cast-iron console with T12 Feed support “Comfort” and MARTIN/Wegoma Variomatic 4N 4-roller feed, variable mechanical adjustment from 12- 65 ft/min (3.5 – 20 m/min.); supplied with tilting joint for easy horizontal and vertical use. 1-1/4″ spindle with spacers and nut. Full set of manuals. (Machine was purchased March/2017). This fully functional machine has been fully cleaned, checked, and is ready to work from the time you receive it. This is our guarantee to both you and your company!

2016 MARTIN T45 PLANER W/80 HOURS

2016 MARTIN T45 PLANER W/80 HOURS $$$RECENTLY SOLD$$$

Martin model T45 thickness planer with 80 hours (absolute hour meter/not re-settable/hour meter runs when head is on only). 24″ width capacity. Digital readout w/ single axis controller for table positioning, 10hp, 220v, 3ph main motor w/ safety brake, infinite feed speeds, Tersa cutterhead, rubber infeed/outfeed rollers, waxlit tray, central lube pump, 24″ x 47″ outfeed table extension. (Machine was purchased March/2017) This fully functional machine has been fully cleaned, checked, and is ready to work from the time you receive it. This is our guarantee to both you and your company!

2007 TIMESAVERS 3 HEAD 2300 SERIES 43″ WIDEBELT SANDER W/4,358 HOURS

2007 TIMESAVERS 3 HEAD 2300 SERIES 43″ WIDE BELT SANDER W/4,358 HOURS $$$RECENTLY SOLD$$$

Clean Timesavers 2300 series 3 head widebelt sander with 4,358 hours. First head is a 25 hp helical grooved 8″ rubber drum. Second head is a 20 hp helical grooved 8″ rubber drum. Third head is a combination head with a 15 hp helical grooved 6″ rubber drum. Platens (2 included) have a 2″ wide face and have NEW graphite and NEW felt. Dial indicators on all drums and platens. The feed is VFD controlled from 20-45 FPM and features a centralized control panel with digital thickness readout (w/NEW battery for memory). Also includes an Auto set up device for thickness. The feedmat is less than a year old and is a 3 ply rough top brown nitrile mat. Double infeed and outfeed holddown rolls. Main motor load meters/Watt meters. Four bed jack screws.  43″ X 75″ abrasive belt size. Disc brakes on main motors. Motorized lift with 0-5″ . 14″ infeed loading area. 15″ minimum part length. Full set of original manuals.

2014 HAFELE FUTURA 250 HINGE BORING, RTA, DRILLING & INSERTION MACHINE $2,000

2014 HAFELE FUTURA 250 HINGE BORING, RTA, DRILLING & INSERTION MACHINE $2,000

This machine is set up to drill and insert RTA fittings currently. Very hard to find used plus it’s a 2014 model year. Powered by a 1-1/2 hp 230V/3 Phase motor. Pneumatic drilling unit with push button controls. (also has optional foot pedal) 10’6″ back fence with 4 flip stops.. Worktop 600 x 400 mm (23 5/8” x 15 3/4”). Dual pneumatic hold-down clamps. Locking pin for fence depth adjustment with positive stops. You can also purchase heads for hinge boring and line boring as well.  This fully functional machine has been fully cleaned, checked, and is ready to work from the time you receive it.

DIEHL SL-52 WIDE ARM GLUE LINE STRAIGHT LINE RIP SAW

DIEHL SL-52 WIDE ARM GLUE LINE STRAIGHT LINE RIP SAW $RECENTLY SOLD$

The chain on this SL-52 WA has 90%+ chain life or better left in it. Just look at the pictures! This is a glue line capable machine. The arbor runs smooth and true. It is powered by a 15 HP motor while the feed is powered by a 2 hp motor. The feed runs as smooth as the arbor and is capable of speeds from 65-195 FPM. 2″ arbor with an 18″ blade capacity can cut material from 1/8″ to 4-1/4″. The table measures 95″ X 79″ and the fence will lock 53″ to the right of the blade with 56 total inches of clearance from the right of the blade to the upright supports. Front adjustable fence locks tight. Automatic chain lubrication system. 1 upper infeed anti-kickback safety guard. 8 spring loaded pressure hold down rollers that are all in very good condition. Adjustable pressure beam with front hand wheel and height controls. Everything raises and lowers throughout it’s range very easily. Front push button controls. Machine weight 6,000 lbs.

LOBO DOUBLE SIDED OSCILLATING EDGESANDER $3,400

LOBO DOUBLE SIDED OSCILLATING EDGESANDER $3,400

Smooth running double sided oscillating edgesander (Lobo model EGS-947) Max. sanding area 9″ X 48″. Main motor is 5 hp and the machines is currently wired 230V/3 Phase. NEW graphite on both platens. This fully functional machine has been fully cleaned, checked, and is ready to work from the time you receive it.

  • Sand paper automatically oscillates up & down, so it will not overheat to get longer life usage and better finish result.
  • 8″ x 20″ end table mounted at left side of the machine to use as contour sanding.
  • Heavy gauge sheet metal cabinets stand and table for heavy work.
  • The height of front & back table is adjustable for 5″.
  • Easily adjustable belt tension device.
  • Two 47″ W x 11-3/4″ D working tables can be tilted up to 45 degrees, reducing material burning and promotes longer belt life.
  • The graphite pad lubricates the sanding belt and allows the belt to run cooler and smoother.
  • All sealed long-life ball bearings and rubber contact motor pulley.
  • Several typical profile blocks can be used for the edge profile sander.
  • Powerful industrial motor for durability usage.
  • Overload protect magnetic switch.

RFS 20KW RADIO FREQUENCY GLUER $10,000

RFS 20KW RADIO FREQUENCY GLUER $10,000

Single owner shuttle style machine. 20 KW radio frequency generator with an 80″ X 36″ X 4″ capacity. Material is clamped from 3 sides via 4 top, 3 edge, and 9 side hydraulic pushers.  Built in timer and adjustable RF. A very nice clean and complete machine with a large 20KW generator.

FLETCHER FM-2001 TOP AND BOTTOM TRIMMER $4,000

FLETCHER FM-2001 TOP AND BOTTOM TRIMMER $4,000

These are made by Fletcher and were also sold under the Delmac brand for well over a decade. Very well built and this machine can handle 3 mm material! Over head control panel for easy operator access, Non-marring phenolic top, heavy fabricated steel base, polished chrome copy shoes w/ fine adjustment screw for accurate and uniform trimming, trimming motors mounted on linear bearings, upper trimming unit adjusts for 1/2″ to 2-1/4″ thick panels, spring loading for constant pressure, top and bottom 0.7 HP motors that are adjustable from 0-12,000 RPM with inverter drive. Pneumatic cylinder w/foot pedal control for rasing and lowering of upper trim unit. This fully functional machine has been fully cleaned and checked and is ready to work from the time you receive it. Currently wired 230V/3 Phase

 

 

 

 

PINHEIRO PMC 4-450 18″ 4 SIDED PLANER SOLD

PINHEIRO PMC 4-450 18″ 4 SIDED PLANER $$$SOLD$$$

Very very clean and well maintained PMC 4-450! This is the original condition……original paint……….this Pinheiro has a lot to offer and is in top condition. The beds show a minimal amount of wear for a machine this age. Top 4 knife cutter-head is powered by an 18 hp motor while the bottom 4 knife cutter-head is powered by a 12 hp motor. The 40 mm side spindles are 9 hp each. The feed is powered by a 5 hp motor and has been upgraded with a variable frequency drive to have more control over the feed speed.  18″ X 8″ capacity. 3 Accurate Technology PRO-Scales have been added for accurate height adjustment. Over head spring loaded feed wheels on the out feed.  Comes very complete with multiple wrenches and PanHans blade setting jigs. This fully functional machine has been fully cleaned, checked, and is ready to work from the time you receive it.

DELMAC DMG 62CT or FRAVOL AZ/2 TOP & BOTTOM TRIMMER $3,000

DELMAC DMG 62CT or FRAVOL AZ/2 TOP & BOTTOM TRIMMER $3,000

This is a low use Italian made Fravol AZ/2 top and bottom trimmer distributed by Delmac in North America as a DMG 62CT. Mechanically it is in excellent plus condition. It’s only downfall is that it has scratches on the case as the previous owner moved it around when he needed it. It has dual .7hp motors on floating heads and is capable of trimming up to 3mm material. The motors are high speed spindles running up to 12,000 rpm and are run on single phase 220V power. Heads are foot pedal activated. SPECS: Shaft diameter-16mm, Shaft height-50mm, Mininmum inside trimming radius-20mm (3/4″), Panel thickness min/max 5/8″- 2 1/4″, Table top size-25 1/2″- 39 1/2″.

1995 NORTHFIELD 24″ JOINTER SOLD

1995 NORTHFIELD 24″ JOINTER $$$SOLD AS IT LISTED$$$

This machine was used sparingly in a pattern shop and is a single owner machine. What also makes it a great find is that it is a 1995 model. It is wearing it’s original paint and has no repairs. It also features a 10 hp 230/460V Reuland motor currently wired 230V. 4 Knife cutter head with electric brake. Tables are dead flat! Is anyone even surprised? This fully functional machine has been fully cleaned and checked and is ready to work from the time you receive it.